Hot Racing

Aluminum piggyback shocks with adjustable rebound for the most Scale 1/10 SCX10 trucksFEATURES:- CNC 6061-T6 billet aluminum shock damper tubes are hard anodized- CNC aluminum ball ends and shock...

Hot Racing dual motor, high torque, winch for superior scale looks and power FEATURES: - High torque dual motor and gearbox reduction design - Full CNC machined billet aluminum case, anodized...

This is the Hot Racing Front Axle Assembly for the Axial SCX-10. FEATURES CNC milled aluminum housing CNC machined billet center housing, axle...

Hot Racing brass axle tube weights for the Axial SCX10, Dingo, Honcho, AX10 Scorpion, and Scorpion. Adds weight where you need it - down low! FEATURES: - CNC machined solid billet brass -...

Hot Racing 20mm wheel hub extensions with 12mm hex for the Axial SCX10, SCX10 II, and WraithFEATURES:- Extends the track width for a wider stance and greater control and stability- Extensions fit...

Hot Racing 15mm wheel hub extensions with 12mm hex for the Axial SCX10, SCX10 II, Wraith and 1.9 WraithFEATURES:- Extends the track width for a wider stance and greater control and stability-...

Hot Racing 18mm wheel hub extensions with 12mm hex for the Axial SCX10, SCX10 II, and Wraith Crawler FEATURES: - Extends the track width for a wider stance and greater control and stability -...

Hot Racing aluminum rear bumper with LED light buckets and tow shackles for the Axial SCX10 Dingo, Jeep, and Honcho FEATURES: - CNC machined billet aluminum bumper, anodized semi-flat black -...

Hot Racing aluminum tire carrier for the Axial SCX-10 Jeep FEATURES: - CNC machined billet aluminum, anodized black - Pre-drilled to mount directly to the stock Axial bumper, AX80126 YOU WILL...

Hot Racing 1/10th scale rear bumper with tow shackle D-rings, LED light mounts, and winch mount for the Axial SCX10 FEATURES: - CNC machined solid billet aluminum construction - Feels very...

Hot Racing front bumper with 5mm LED light buckets and clevis mounts for the Axial SCX10 FEATURES: - Billet CNC machined aluminum - Anodized black and silver - Integrated brush guards -...

Optional Hot Racing Hardened Steel 32P 54T Spur Gear for use on the Arrma 1/10 2wd Associated SC10.GT2 T4 or B4 FEATURES: - Hardened steel construction - Rugged 0.8 Module/32pitch teeth for...

This is the Hot Racing Rock Racer Conversion Chassis for the Axial AX-10 Vehicles.       FEATURES CNC machined aluminum...

Hot Racing steel super duty Steel Spur Gear 91T 48P spur gear for 1/10 Arrma 4X4 brushed vehicles. See comments below for specific vehicle fit information.FEATURES:- Rugged Steel 48 pitch for total...

Optional Hot Racing Hardened Steel 32P 57T Spur Gear for use on the Arrma 1/10 2WD Specially make to handle brushless power FEATURES: Hardened steel construction Rugged 0.8...

CNC Stainless Steel Skid plate Set FEATURES: CNC from a single piece of 3mm stainless steel plate.  it fit over the front and rear of the chassis Reduce skid and scrape damageAct as...

Hot Racing replacement brass flange bushings for the Hot Racing 1/8 Yeti XL YEX4801 steering system FEATURES: - CNC machined brass YOU WILL RECEIVE: - Four (4) brass...

Hot Racing shock Cap rebuild kit for the Hot Racing XMX156M XMX156R shock capFEATURES:- Restores proper performance to worn o-ring- Rebuilds two shocksYOU WILL RECEIVE:- Two (2) 1.9mm thick, 23mm OD...

Hot Racing extra-lift cold-coiled shock springs for the Traxxas E-Revo, Revo 3.3, Slayer Pro 4X4, and Summit. These springs are approximately 5mm longer than the stock springs to help compensate and...

Hot Racing aluminum servo saver steering for the 1/10 Traxxas E-Revo, E-Revo 2.0, Revo, Slayer Pro 4X4, and SummitFEATURES:- CNC machined aluminum construction, anodized blue- Includes heavy duty...