Inferno MP777

Much longer lasting shoe compared to KYOIF136. Performs much like the older shoe with less grab, a bit more forgiving. As these wear in the clutch file off the burred edges. If the spring is in danger of being touched by the clutch bell due to wear,...

As these wear in the clutch file off the burred edges. If the spring is in danger of being touched by the clutch bell due to wear, replace the shoes! Common across all the Kyosho Inferno series of 1/8th scale RC Nitro Cars from the MP7.5 (Neo, Sports...

For the Famous Kyosho Clutch. Common across all the Kyosho Inferno series of 1/8th scale RC Nitro Cars from the MP7.5 series to the MP777's. You can upgrade your Readyset kit such as the Inferno GT2 or ST US Sports 2 with the 3 shoe clutch.

Common across all the Kyosho Inferno series of 1/8th scale RC Nitro Cars from the MP7.5 series to the MP777's including optional upgrade for the Inferno GT and GT2.

Common across all the Kyosho Inferno series of 1/8th scale RC Nitro Cars from the MP7.5 series to the MP777's and the MP9.   Also use on Kyosho readyset kits like the Inferno GT, GT2 and US Sports. The best fuel filter out there. Many drivers...

Kyosho heavy duty air cleaner sponge for the Inferno Neo,  GT or the MP777 and 7.5 Tuggies and Buggies. Package of 4 (inner). This is also the stock air filter element for the Kyosho DRX, DMT and DRT.

The Kyosho Inferno VE side guard set is also compatible with the MP7.5 sports series, ST and the Inferno GT and GT2.. Gives you the correct amount of space for brushless conversions on these cars.This part replaces the discontinued part KYOIF11.Can be...

Common across all the Kyosho Inferno series of 1/8th scale RC Nitro Cars from the MP7.5 series to the MP777's. The 2.8mm rear sway bar is the same as the stock ones on  the off-road race kits. Sway bars are used to make adjustments to the handling...

This 8x16x5 metal shield Bearings used for the hubs and differentials in the Inferno MP9, MP777 and MP 7.5 series cars and trucks. This includes the Inferno MP9, Neo, VE, MP777 WC,  STRR, GT and GT2, the ST and ST2 US Sports truggies, the US...

Common across all the Kyosho Inferno series of 1/8th scale RC Nitro Cars from the MP7.5 series to the MP777's. Includes the spacers for setting the car's wheelbase. Made for plastic/composite material. Usually these hubs would last forever but the...

Also refereed to by Kyosho as a Differential Shaft set.Made of high quality hardened steel. Replace the out drives in your differentials. Includes 4 shims for setting the proper ring gear/Pinion mesh. his is very important to minimize the the wear...

Used for the ball ends on the steering tie rods on the Inferno MP9, MP777, GT, GT2, VE, Neo, 7.5 Family of buggies and truggies. Made from hardened and polished steel, long lasting.Also use don the MFR Monster truck, MadForce Kruiser, MadForce Kruiser...

Antenna tubes with antenna tube caps for Kyosho Inferno MP9, MP7.5 and Inferno MP777 cars and trucks. Also used on the Lazer ZX-5 kit and Readyset, Ultima RB5 and RT5 or almost any RC Car.

The Kyosho Inferno Differential Bevel Shafts are used in the differentials for holding the spider gears. Made of hardened steel and painted black. These shafts need replacing if they show wear around the shaft near the end. The Differential spider gear...

These rear skid plates are for the Kyosho MP777 / ST-R / ST-RR / NEO / Inferno VE.

This front BumpSkid plate is for the Kyosho MP777 / ST-R / ST-RR / NEO / Inferno VE.

96643 5x7mm Shim Set 5X7mm shims used for spacing 1/10 rear axles. 0.1, 0.2, 0.3mm sizes 10 each.

These gaskets can be reused after a fluid change, but after 3 or more uses usually start to leek. Ensure the diff case gasket surface is smooth before Installing new gasket. Use 250 grit or higher sand paper on a flat surface to sand the diff case...

The Kyosho Inferno differential cases generally last for a long time without needing replacement. However if you have a blown bearing in your bulkhead or tighten the ring gear screws to tight and strip the case then you will need to replace them...

Includes 2 sun gears and 4 spider gears. These are the all gears used internally in one differential. They generally wear well, however as you differential gets older or has leaked all the fluid out from a damaged seal you will see wear on them...

Optional springs for the Kyosho clutch. Harder springs will cause the clutch shoes to engage at a higher RPM. If you find you need a bit more punch on the bottom RPM of your car this will help. You can tune the Kyosho clutch using soft springs (0.9)...

Optional springs for the Kyosho clutch. Softer springs will cause the clutch shoes to engage at a lower RPM. If you find you need to smooth out the bottom RPM of your car on loose surfaces, this will help. For use with the MP9, MP777 and 7.5. You can...

Optional springs for the Kyosho clutch. Softer springs will cause the clutch shoes to engage at a lower RPM. If you find you need to smooth out the bottom RPM of your car on loose surfaces, this will help. For use with the MP9, MP777 and 7.5. You can...

Common across all the Kyosho Inferno series of 1/8th scale RC Nitro Cars from the MP7.5 series to the MP777's and MP9. These are the Stock Spring rate for the clutch.Also used on the DRX, DRT, DBX and DST clutches as well as the Madforce Kruiser.