Traxxas

 

.

.

FEATURES: Aluminum construction          Silver in colorINCLUDES: Two Shock Shafts

This is an optional Traxxas RPM Sensor Mount Set, and is intended for use with a Traxxas nitro vehicle when wanting to use the optional Traxxas RPM sensor (TRA6520/TRA6522). The sensor mount...

FEATURES: Replaces damaged or worn spur gears Constructed of plastic INCLUDES: One 43 Tooth 1st Speed Spur Gear for the Traxxas T-Maxx Truck REQUIRES: Installing in gearbox between the drive hub...

.

FEATURES: Nylon and rubber constructionINCLUDES: Two Diff Gear Covers          Two Large O rings          Two...

Fits Continued: 1/10 Slash R.G.D. / Ford Raptor / Nitro Jato 3.3 / Revo / T-Maxx FEATURES: Machined blue aluminum ball bearing equipped wheels Rubber Tires INCLUDES: Two rubber tires, four 5x8mm ball...

FEATURES: Black nylon construction INCLUDES: One upper rear suspension arm One lower rear suspension arm REQUIRES: Nothing. These are direct replacement parts. COMMENTS: Since these are symmetrical,...

 

FEATURES: Black nylon construction INCLUDES: One upper rear and one lower rear suspension arm REQUIRES: Removing stock suspension arms Adjusting camber and toe after installing Adjustable Suspension...

FEATURES: Steel construction   INCLUDES: One Pinion Gear with set screw

FEATURES: Replaces damaged or worn idler gears Constructed of steel INCLUDES: One 16 Tooth Steel Idler Gear for the Traxxas T-Maxx Truck One 3x6mm and one 8.3x8mm flat metal washers One 8x12x0.5mm...

FEATURES: Plastic construction, white in color INCLUDES: Two Dish Rear Wheels in White REQUIRES: Tires Tire Glue  SPECS: Diameter: 3.4" (87mm) Width: 2" (51mm) Hex Size: 17mm

.

  This is the Traxxas 8.4V 3300mAh Hump NiMH Battery Pack. FEATURES New high current connector with gold-plated copper...

FEATURES: Steel construction   INCLUDES: One Pinion Gear with set screw

.

FEATURES: Prevents moisture and dirt from entering receiver boxINCLUDES: Silicone O-ring          Silicone...

FEATURES: Anodized aluminum construction, red in color Black nylon ball ends and steel link set INCLUDES: One 39mm red aluminum turnbuckle set with instructions REQUIRES: Installation onto vehicle

FEATURES: Fastens to bulkhead and helps to support axle carriers Black in color, constructed of hardened plastic INCLUDES: One Right and one Left Upper Suspension Arm for the T-Maxx 3.3 REQUIRES:...

FEATURES: Red in color Orange band on spring indicates 3.2 tension rating INCLUDES: Two 3.2 rear shock springs REQUIRES: Nothing. These are direct fit springs. SPECS: Length: 1-3/4" (44mm) Outer...

FEATURES: Blue anodixed aluminum (2.5mm thick) INCLUDES: One front & one rear Tie Bar w/one 3x10mm button head screw TRAC2577 REQUIRES: TRAC2579 2579 Button Head Screw 3X15mm for rear COMMENTS:...

FEATURES: Steel construction   INCLUDES: Three Pinion Gears with set screw

FEATURES: Red plastic shock pistons with 2 x.5mm holes          Back plastic travel limitersINCLUDES: Four shock...

FEATURES: Steel construction   INCLUDES: Three Pinion Gears with set screw

Fits Continued: 1/10 Slash R.G.D. / Nitro 4-Tec / Nitro Slash / Nitro Sport / Nitro Stampede / T-Maxx / Nitro Rustler / T-Maxx Classic These rubber cap diaphragms for Traxxas plastic shocks, also...

These are replacement Main Frame Lower Portion for the LaTrax Alias Quad-Copter Includes: 1 x Black Main Frame Lower 4 x 1.6x5mm BCS (self-tapping) screws

  FEATURES: Made of Stainless steel Shielded on both sides (not rubber sealed) SPECIFICATIONS: 5mm inside diameter 11mm outside diameter 4mm thick INCLUDES: 8 ball bearings COMMENTS: Can be used...

.

FEATURES: White plastic construction INCLUDES: One 21T 1st speed gear One 18T input gear REQUIRES: Installation into Traxxas E-Maxx  

Fits Continued: 1/10 Ford Raptor / Rally VXL / Slash R.G.D. / Nitro Jato 3.3 / Nitro 4-Tec / Revo / T-Maxx / Slayer Pro 4x4 FEATURES: Metal...

Fits Continued: 1/10 Ford Raptor / Rally VXL / Slash R.G.D. / Nitro Jato 3.3 / Nitro 4-Tec / Revo / T-Maxx / Slayer Pro 4x4 / Nitro Rustler / T-Maxx Classic FEATURES: Steel...

.

FEATURES: Steel construction Phillips drive insert Lower shock attachment screws INCLUDES: Six Ball Screws for the Traxxas 4-Tec Electric Powered 4 Wheel Drive Sedan.

Fits Continued: 1/10 Slash R.G.D. / Rally VXL / Nitro Slash / Revo / T-Maxx / Slayer Pro 4x4 / T-Maxx Classic FEATURES: Aluminum construction, blue anodized in color INCLUDES: Four aluminum splined...

.

FEATURES: Steel construction   INCLUDES: One Pinion Gear with set screw

FEATURES: Plastic and steel construction INCLUDES: 2 Stub axles REQUIRES: Installation on vehicle

This is a pair of 5A Fuses for the Traxxas #2974, #2975, #2977 AC Powered Chargers. FEATURES Glass tube type fuses ...

.

These are the Traxxas Flat-Head 3 x 15mm Machine Screws. FEATURES: Metal construction Black in color INCLUDES: Six 3 x 15mm Flathead Hex Machine Screws REQUIRES: Installation on the vehicle

FEATURES: Durable blue plastic construction INCLUDES: 3 plastic cases and rubber sealing items, instruction sheet REQUIRES: Application into servo case per instructions

FEATURES: Replaces damaged pivot ball aluminum caps. Constructed of aluminum. INCLUDES: Four pivot ball aluminum caps for the Traxxas T-Maxx. REQUIRES: Threading two caps into each axle carrier...

This is an optional Traxxas Telemetry Trigger Magnet Holder and Spur Gear Magnet. This component installs onto the spur gear and holds a magnet that is detected by the RPM sensor (TRA6520, TRA6522)...

(for use with remote push button)

.

.

FEATURES: Nylon Construction           Black in Color   INCLUDES: Three Spur Gears

.

FEATURES: Plastic construction, white in color INCLUDES: Two Dish Front Wheels in White REQUIRES: Tires Tire Glue SPECS: Diameter: 3.4" (87mm) Width: 1.7" (43.4mm) Hex Size: 17mm

FEATURES: Constructed of hardened steel INCLUDES: Differential Output Gear for the Traxxas Revo 3.3 REQUIRES: Installing in front or rear of center differential COMMENTS: WIll not work with Rear...

FEATURES: Rubber construction Blue in color Flexible material INCLUDES: Two Blue rubber Shock Boots and Two black Plastic Shock Caps. REQUIRES: Nothing SPECS: Length: 1 3-8" (35mm) Diameter: 1/2"...

This is a pair of Assembled Traxxas SCT Tires and 5-Spoke Wheels. FEATURES Fits the front of 2WD short course trucks Split-spoke beadlock style...

FEATURES: Standard bearings. INCLUDES: Eight 5mm x 8mm Bearings REQUIRES: Assembly into the model. SPECS: Height: 2.5mm Inner Diameter: 5mm Outer Diameter: 8mm

FEATURES: Aluminum Construction Anodized Red INCLUDES: (2) Assembled Turnbuckles REQUIRES: Installation onto Stampede 5mm Wrench SPECS: Length: 2.4" (61mm)

FEATURES: Nylon construction INCLUDES: Gear, two ring seals, gasket and instruction sheet REQUIRES: Installing in diff case according to instructions on sheet COMMENTS: Fits only the optional Revo...

.

FEATURES: Steel construction, gun metal in color Replaces a worn or damaged idler gear INCLUDES: One 13 Tooth Idler Gear (first speed gear) REQUIRES: Installation

Includes: LED lights, chassis harness (4 clear lights, 2 red lights) (1)/wire tie (3) Requires: power supply #7286

FEATURES: Plastic construction Black in color INCLUDES: One Rear Bumper. REQUIRES: Assembly onto Vehicle

FEATURES: Nylon construction           Black in color INCLUDES: Three Spur Gears

.

FEATURES: Steel construction Round head with phillips drive insert INCLUDES: Six screws SPECS: 3mm thread size 20mm long

Fits Continued: 1/10 Nitro Slash / Nitro Sport / Nitro Stampede / T-Maxx / Nitro Rustler / T-Maxx Classic FEATURES: Aluminum construction Gunmetal colored INCLUDES: One Big Bore XXL Shock Body...

.

FEATURES: Metal construction White in color Damper rating 1.3 INCLUDES: Two Super Shock Springs Gold 1.3 REQUIRES: Assembly onto Vehicle

.

The unique patent-pending Traxxas adjustable wheelie bar features four position adjustment, plus it quickly and easily installs onto the rear of any electric Slash, Rustler, Stampede, and Bandit. The...

FEATURES: Gray plastic construction "Long Travel" raised lettering on top of the rocker arms INCLUDES: (8) rocker arms, Part #5356 REQUIRES: Installation on the Traxxas Revo SPECS: Length: 2" (52mm)...

FEATURES: Metal construction INCLUDES: (12) Washers SPECS: Size: 3x6mm

These are the 4x15mm Button Head Machine Screws for the Traxxas X-Maxx Monster Truck     FEATURES Steel construction   ...

Includes: 2- 26mm Hard chrome suspension ("hinge") pins. 4- 3mm E-rings.

This is the Traxxas Power Cell 7.4V 2200mAh 25C 2S LiPo Battery.   FEATURES Semi rigid construction does not require a hard case and...

.

FEATURES: 0.12" (3mm) thick 6061 aluminum, dark titanium in color INCLUDES: XO-1 Chassis  

FEATURES: Replaces stock output shafts, constructed of steel. Spacer is made of plastic. INCLUDES: One output shaft and spacer REQUIRES: Installing shaft in gearbox between the clutch bell and output...

FEATURES: Black nylon construction INCLUDES: One upper rear and one lower right rear suspension arm REQUIRES: Removing stock suspension arms Adjusting camber and toe after installing Adjustable...

FEATURES: Aluminum construction, anodized blue in color INCLUDES: Motor Mount with Instruction Sheet

Fits Continued: 1/10 Nitro Sport / Nitro Stampede / Nitro Rustler Package includes: 2ea aluminum shock caps Specs: diameter- 14mm height- 17mm

.

FEATURES: Made of stainless steel This is used to hold the front steering block (TRAC9036 #3636) to the castor block (TRAC9032 #3632) on the electric (not Nitro) Rustler Also called the vertical...

This is the Replacement Battery Door for the 2.4GHz Transmitter for the LaTrax Alias Quad-Copter Includes: 1 x Battery Door

FEATURES: Aluminum Construction, hard anodized coated Threaded for Easy Adjustment INCLUDES: One hard anodized Threaded Aluminum GTR Shock Body REQUIRES: Assembly onto Vehicle Parts to Complete Shock...

Split-Spoke 3.8" wheels for Revo & Maxx trucks add another dimension of style and performance. Available in black-chrome, mirror-chrome and satin finish, Traxxas Split-Spoke wheels...

EATURES: Cast aluminum construction INCLUDES: One manifold REQUIRES: Nothing. This is a direct replacement part. SPECS: Outlet inner diameter: 11mm (0.43") Engine side inner diameter: 13mm (0.51")

Damper balls, anti-vibration, gimbal (4) (yellow dot)/ camera mount (4) for Traxxas Aton

.

This is the Servo Case and Gaskets for the Steering Servo used on the Traxxas X-Maxx Monster Truck     FEATURES Replaces damaged case...

FEATURES: Steel construction   INCLUDES: Three Pinion Gear with set screw

.

FEATURES Molded plastic composite construction   INCLUDES Left and Right Stub Axle Carriers

 

FEATURES: Blue and Grey in Color Rubber and Nylon Construction INCLUDES: Two Rubber Diaphragms Four Shock Pistons Two Shock Ends Two Ball Ends Two Rubber O-Rings REQUIRES: Installation into Shocks.

Fits Continued: 1/10 4-Tec  / Nitro Slash / Nitro Sport / Nitro Stampede / T-Maxx / Nitro Rustler / T-Maxx Classic   Includes: 4 short rod ends (17mm) 16 long rod ends (19mm) 2 ball...

.

FEATURES: Molded plastic construction INCLUDES: Center Bearing Carrier

.