Traxxas

  FEATURES: Plastic Construction, Black Chrome in Color INCLUDES: One Front and one Rear Bumper REQUIRES: Installation SPECS: Front Bumper Rear Bumper Length: 104mm (4.09") Length: 116mm (4.57")...

FEATURES: Nylon Construction Black in Color Allows for Oversized Bearing use INCLUDES: One Left Axle Carrier One Right Axle Carrier Four Dust Boot Retainers Two Bearing Spacers REQUIRES: Installation

FEATURES: Replaces damaged axle carriers and steering blocks. Constructed of black plastic. INCLUDES: One set of axle carriers and steering blocks for the Traxxas Revo. REQUIRES: Bolting to each...

FEATURES: Durable black nylon construction INCLUDES: One upper LEFT FRONT suspension arm One lower LEFT FRONT suspension arm REQUIRES: Suspension pin set to attach to bulkhead SPECS: UPPER LOWER...

FEATURES: Black plastic construction Rocker shafts preinstalled INCLUDES: Front bulkhead halves Part #5330 (2) rocker shafts Part #5354 (4) 4X14mm button head screws  

FEATURES: Black plastic construction Rocker shafts preinstalled INCLUDES: Rear bulkhead halves Part #5329 (2) rocker shafts Part #5354 (4) 4X14mm button head screws

FEATURES: Nylon construction Black in color INCLUDES: One Stering Servo Cover Plate REQUIRES: Installation on the vehicle SPECS: Length: 55mm (2.17") Width: 20mm (0.79") Height: 9mm (0.35")

FEATURES: Black plastic construction INCLUDES: Four steering servo mounts REQUIRES: Nothing. These are direct replacement parts. COMMENTS: Since the Revo uses two steering servos, the vehicle...

FEATURES: Constructed of plastic Holds the high torque and micro servos for the throttle/brake operation and transmission shift INCLUDES: Traxxas Left Electronics Box with lid REQUIRES: Installing on...

FEATURES: Nylon construction, black in color INCLUDES: One Throttle Servo Mount Two 4x10 Socket Head Screws REQUIRES: Installation SPECS: Length: 80mm (3.15") Width: 27mm (1.06") Height: 20mm (0.79")

FEATURES: Black plastic construction Accomodates either AA battery holder or RX flat pack INCLUDES: One receiver box with cover One battery box with cover Rubber charge jack plug Foam pad and...

FEATURES: Black plastic construction INCLUDES: One right electronics box One box cover/charge jack plug Three pieces of adhesive backed foam padding REQUIRES: Nothing. These are direct replacement...

FEATURES: Anodized aluminum (2.5mm thick) INCLUDES: One front & one rear Tie Bar w/one 3x10mm button head screwREQUIRES: 2579 Button Head Screw 3X15mm for rear COMMENTS: The flat tie bar is for...

FEATURES: Steel construction Polished finish INCLUDES: Two Long Suspension Pins Four Short Suspension Pins SPECS: Long Suspension Pin Length: 85mm (3.35") Short Suspension Pin Length: 24mm (0.95")...

These are the (optional) Steel Pushrods for the Rocker Arms These go between the Rocker Arms and the Lower Suspension Arms FEATURES: Black steel construction INCLUDES: Two Pushrods w/pre-installed...

These are the (optional) Red Aluminum Pushrods for the Rocker Arms These go between the Rocker Arms and the Lower Suspension Arms **Must be used with Progressive-1 Rocker Arm Set, .** FEATURES: Red...

  FEATURES: Metal pushrod construction Plastic rod ends with hollow ball ends INCLUDES: (2) pushrods (4) rod ends (4) hollow ball ends REQUIRES: Installation on a Traxxas Revo SPECS: Pushrod...

FEATURES: Black plastic construction INCLUDES: One front shock mount One rear shock mount Four chassis wire clips Four 3x32mm caphead machine screws Four 3x6mm buttonhead machine screws  

FEATURES: Black plastic construction "TRX" logo on front body mount INCLUDES: Front and rear body mounts Part #5314 Front and rear body post Part #5314 (4) 2.5X18mm screw pins (1) 4X10mm button head...

FEATURES: Button head machine screws. Starter attachment screws with threadlock. INCLUDES: Six screws. SPECS: Length: 12mm Diameter: 3mm

.

.

This is the EZ Start 2(R) Starting System from Traxxas. This is the updated replacement for the first-generation EZ Start 2 System. It features a higher torque motor for the new 3.3 race...

FEATURES: Replaces worn or damaged air filter components INCLUDES: Foam Filter Element with Plastic Holder with Body Clip, Rubber Connector and Wire Bracket

FEATURES: Replaces damaged or dirty air filter assemblies Plastic body with foam element and rubber attachment hose INCLUDES: Foam filter and pre filter, support cap, filter base and wire mount and...

FEATURES: Replaces damaged or dirty air filter assemblies Plastic body with foam element and rubber attachment hose INCLUDES: Foam filter and pre filter, support cap, filter base and wire...

FEATURES: Plastic construction Black in color INCLUDES: One Air Filter Housing One Foam Insert Element One Rubber Filter Base One Cable Tie SPECS: Diameter at Mounting Base: 0.55" (14mm) Diameter of...

FEATURES: Black plastic air filter housing with cover screen and and changeable element Rubber double angled neck for filter Zip tie for fastening INCLUDES: One screened filter One rubber double...

FEATURES: Constructed of foam and pre-oiled to trap dirt Pre-Filter for extra filtration INCLUDES: Three Air FIlter Inserts for the Traxxas 3.3 engine SPECS: Height: 38mm (1.5") Diameter: 38mm (1.5")

FEATURES: Constructed of foam and pre-oiled to trap dirt INCLUDES: Three Air FIlter Inserts for the Traxxas 2.5 (TRX 2.5, 2.5R, 3.3) engine REQUIRES: Installing in air filter boot on engine SPECS:...

FEATURES: Black plastic air filter housing with cover screen and and changeable element Rubber angled neck for filter Rubber adapter for filter Zip tie for fastening INCLUDES: One screened filter One...

FEATURES: Red silicone construction. INCLUDES: One 12.2x1mm o-ring. REQUIRES: Nothing. This is a direct replacement part.

FEATURES: Spring constructed of steel INCLUDES: One header spring One black rubber gasket One white nylon gasket REQUIRES: Fastening header to engine with spring

.

.

FEATURES: Silicone construction Blue in color INCLUDES: One Tune Pipe Coupler One Exhaust Deflector (for use on the tune pipe) One short Tie-Strap Two long Tie-Straps REQUIRES: Assembly to...

FEATURES: Metal construction. Used on the Traxxas TRX 2.5. engine INCLUDES: (1) Flywheel Nut

.

This is the End Cap and O Ring for the carburetor of the Traxxas 2.5 engine. This end cap threads into the carburetor body on the opposite side of the low speed needle. FEATURES: End cap is...

.

.

FEATURES: Fits Traxxas 1/10 scale nitro vehicles Replaces worn or damaged clutch bells Constructed of hardened steel INCLUDES: One Traxxas 17 Tooth Steel Clutch Bell Two 5mm x 8mm 0.5mm fiber washers...

FEATURES: Metal construction Five cooling holes on the face of bell (bellow the teeth)INCLUDES: One clutch bellTwo washersTwo e-clipREQUIRES: This clutch bell uses 5X11 bearings #4611 (not...

FEATURES: Vented clutch bell One piece bell design INCLUDES: One 15 tooth black vented clutch bell Two 5x8x0.5mm fiber washers One 5mm e-clip REQUIRES: Using the original 5x11x4mm clutch bell ball...

FEATURES: Metal construction Five cooling holes on the face of bell (bellow the teeth) INCLUDES: One clutch bell Part #5214 Two washers Part #1985 Two e-clip Part #1633 REQUIRES: This clutch bell...

.

 Fits Continued: 1/10 Monster Mutt / Ford Raptor / Slash R.G.D. / Nitro Jato 3.3 / Revo / T-Maxx FEATURES: Constructed of rubber, black in color with with "TRAXXAS" written in white on the...

These are the 5182A 20 x 27 x 4mm Ball Bearings for the Traxxas X-Maxx Monster Truck     FEATURES Steel construction with black rubber...

FEATURES: Holds all gears including the 2speed gear set and input shaft Gray in color, constructed of hardened plastic Fits front or rear of vehicle INCLUDES: One each Front and Rear Gearbox Halves,...

FEATURES: Stainless Steel bearing construction Blue rubber dirt shields INCLUDES: (2) 6x13x5mm ball bearings Part #5180 SPECS: Inside diameter: 6mm (0.24") Outside diameter: 13mm (0.51") Width: 5mm...

FEATURES: Steel construction Silver in color INCLUDES: Two 59mm screw pins. Four 73mm screw pins. Two 65mm screw pins.

FEATURES: Black plastic construction INCLUDES: One sensor cover (one black plastic plastic construction) One black plastic cover (covers the spot that the optidrive was) One blue rubber...

FEATURES: Steel construction Can be used to replace a bent or damaged front center driveshaft INCLUDES: One steel constant-velocity driveshaft REQUIRES: Dust boots and pins(TRAC5129) SPECS: Length:...

FEATURES: Steel construction INCLUDES: Two steel constant velocity driveshafts Two M4/15 screw pins REQUIRES: Installation onto vehicle. SPECS: Length: 18mm (.70") Diameter: 13mm (.51")

FEATURES: Black plastic construction Pre-installed pressure fitting INCLUDES: One Tuned Pipe for the Traxxas T-Maxx. REQUIRES: Nothing. This is a direct replacement part. SPECS: Length: 114mm (4.49")...

Features:Constant-Velocity Driveshafts are designed to handle Extreme Horsepower and Articulation.Inner and Outer U-joints are Lubricated and Sealed by a Rubber Boot for maximum protection against...

.

FEATURES: Aluminum Construction Silver in Color INCLUDES: Four Aluminum Wheel Spacers REQUIRES: Assembly onto Vehicle

FEATURES: Constructed of steel with serrated flange area for sure grip Nylon insert INCLUDES: Eight 5mm Flanged Nylon Locking Nuts REQUIRES: 8mm nut drivers SPECS: Hex Size: 8mm Inner Diameter: 5mm

FEATURES: Metal Construction Black in Color Hex Head Design INCLUDES: Six 4mm x 15mm Black Metal Screw Pins. REQUIRES: Assembly onto Vehicle 2mm Hex Wrench SPECS: Length (Overall): 15.9mm (0.62")...

FEATURES: 30% lighter than stock steel toe links 4 times stiffer and more than double the strength of aftermarket titanium Unique hollow tube design using 7075-T6 aluminum Anodized black in...

FEATURES: Constructed of steel, polished natural finish INCLUDES: Two Rear Turnbuckles/Toe Links for the Traxxas 3.3 T-Maxx. REQUIRES: Installing between wheel hubs and rear bulkheads SPECS: Length:...

FEATURES: 30% lighter than stock steel toe links 4 times stiffer and more than double the strength of aftermarket titanium Unique hollow tube design using 7075-T6 aluminum anodized fire red in...

FEATURES: 30% lighter than stock steel toe links 4 times stiffer and more than double the strength of aftermarket titanium Unique hollow tube design using 7075-T6 aluminum Anodized black in...

FEATURES: Thicker steel construction. INCLUDES: Two turnbuckles with pre-installed rod ends and balls. REQUIRES: Nothing. These are direct replacement rods. SPECS: Length: 108mm (4.25") Thickness:...

FEATURES: 50K weight oil INCLUDES: 1.75 oz (50cc) bottle of oil w/ 1-1/2" (38mm) pointed fill cap  

Spacer, pushrod (aluminum, blue) (use with 5318 or 5318X pushrod and 5358 progressive 2 rockers) (8)Replacement part for these models:E-Revo BrushlessE-RevoRevoSummitAccessory part for these...

FEATURES: Helps to support axle carriers and shocks Black in color, constructed of hardened plastic COMMENTS: For the 3.3 version only.

FEATURES: Restores performance to worn driveshaft components INCLUDES: Four Rubber accordian style dustboots, pins, and lube for two driveshaft assemblies

FEATURES: Stainless Steel Construction Blue Rubber Sealed INCLUDES: Two 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings REQUIRES: Assembly onto Vehicle SPECS: Outer Diameter: 18mm (0.70") Inner...

FEATURES: Steel Construction Shielded with blue rubber seals INCLUDES: Two Ball Bearings REQUIRES: Assembly to vehicle SPECS: Inner Diameter: 10mm Outer Diameter: 15mm Side Thickness: 4mm COMMENTS:...

FEATURES: Stainless Construction Blue Rubber Sealed INCLUDES: Two 8mm x 16mm Rubber Sealed Bearings REQUIRES: Assembly onto Vehicle SPECS: Inner Diameter: 8mm (0.31") Outer Diameter: 16mm (0.62")...

Ball bearings, black rubber sealed (6x12x4mm) (2)

FEATURES: Steel construction Blue rubber dirt shields INCLUDES: (2) ball bearings, Part #5117 SPECS: Inside diameter: 6mm Outside diameter: 12mm Width: 4mm

Ball bearings, black rubber sealed (5x11x4mm) (2)

Fits Continued: 1/10 Maximum Destruction / Monster Mutt / Ford Raptor / Rally VXL / Slash R.G.D. / Nitro Jato 3.3 / Nitro 4-Tec / Nitro Slash / Nitro Sport / Nitro Stampede / Revo / T-Maxx /...

Ball bearings, black rubber sealed (5x8x2.5mm) (2)

This is a 2 pack of Traxxas 5X8mm Ball Bearings. FEATURES Metal bearing construction Blue rubber dirt shields ...

Oil, shock (80 wt, 1,000 cSt, 60cc) (silicone)Accessory part for these models:1/16 E-Revo® VXL1/16 E-Revo®1/16 Slash 4WD1/16 Summit1/18 LaTrax® Desert Prerunner1/18 LaTrax® Rally1/18 LaTrax®...

Oil, shock (50 wt, 600 cSt, 60cc) (silicone)Accessory part for these models:1/16 E-Revo® VXL1/16 E-Revo®1/16 Slash 4WD1/16 Summit1/18 LaTrax® Desert Prerunner1/18 LaTrax® Rally1/18 LaTrax®...

FEATURES: Clear plastic 500cc capacity bottle Blue anodized aluminum spout INCLUDES: One Fuel Bottle One fuel bottle spout with black plastic cap REQUIRES: Filling with glow fuel. SPECS: Capacity:...

FEATURES: Replaces stock reverse output gear. Constructed of plastic. INCLUDES: One 26 tooth reverse output gear assembly REQUIRES: Installing gear on output shaft in gearbox.

FEATURES: Replaces stock forward output gear. Constructed of plastic. INCLUDES: One 26 tooth forward output gear assembly REQUIRES: Installing gear on output shaft in gearbox.

FEATURES: This is the gear for the shaft that converts the T-Maxx to forward only (4991). Blue plastic construction. 26 tooth gear. Carded packaging. INCLUDES: One 26 Tooth Gear. REQUIRES: Forward...

FEATURES: Fits first generation T-Maxx transmission without Optidrive Steel shaft with plastic gear 22T and 17T gears Pre-assembled on shaft INCLUDES: One transmission input shaft REQUIRES:...

FEATURES: Replaces damaged or worn drive hubs Constructed of aluminum INCLUDES: One Drive Hub Clutch Assembly for the Traxxas T-Maxx One 6x8x0.5mm washer REQUIRES: Installing inside transmission on...

FEATURES: Replaces damaged or worn snap rings Constructed of steel INCLUDES: Two 14mm Snap Rings for the gear hub assembly for the Traxxas T-Maxx REQUIRES: Installing on gear hub assembly (4986)

FEATURES: Metal construction Black in color INCLUDES: One differential spool REQUIRES: Assembly onto a T-Maxx truck.

Fits Continued: 1/10 Slash R.G.D. / Ford Raptor / Nitro Jato 3.3 / Revo / T-Maxx FEATURES: Constructed of hard plastic Axles constructed of steel INCLUDES: Four wheels and two axles REQUIRES:...

FEATURES: Attaches to and protects chassis and transmission Skidplate is gray in color Nylon construction INCLUDES: One Skidplate REQUIRES: Installing on chassis  

FEATURES: Replaces worn brake discs Fiber faced for long life INCLUDES: One Brake Disc REQUIRES: Installing brake adapter (4966), pads (4965) and output yoke (4927) at rear of transmission.

These pins go through the stub axles on each wheel, the wheel hubs are then placed over these pins. FEATURES: Replaces missing axle pins Axle pins are steel INCLUDES: Four 2.5x12mm axle...

FEATURES: Blue anodized. Machined 6061 T-6 aluminum construction. Packaged in foam, on a bubble sealed header card. INCLUDES: Four Hex Wheel Hubs Four 2.5 x 10mm Axle Pins REQUIRES: Assembly onto the...

FEATURES: Replaces missing or damaged hex wheel hubs Hubs are made of molded black plastic Axle pins are steel INCLUDES: Two Hex Wheel Hubs Two 2.5x12mm axle pins REQUIRES: Inserting pins through...

FEATURES: Features heavy duty nylon yokes for long lasting durability. The steel axle extends from the nylon yoke. Black in color. INCLUDES: Two heavy duty stub axles REQUIRES: Assembly onto the...

FEATURES: Durable nylon construction Steel u-joints INCLUDES: Two long external splined half shafts Two long internal splined half shafts Four u-joint connectors REQUIRES: Assembly into a T-Maxx or...

FEATURES: Black nylon construction INCLUDES: Two heavy-duty short half-shafts (external-splined) Two heavy-duty short half-shafts (internal-splined) Four metal U-joints REQUIRES: Nothing, direct...

FEATURES: Clear, nylon construction Black fuel tank cap (spring loaded) INCLUDES: One fuel tank One Pre-installed lid with spring One Pre-installed pressure tap REQUIRES: Assembly on to Traxxas...

FEATURES: Stock aluminum steering bellcranks. Steering link is steel and rods ends are plastic. INCLUDES: Two bellcrank posts One 3x25mm steering link threaded rod with rod ends REQUIRES: Placing...

FEATURES: Replaces stock steering bellcranks. All components are plastic, except for the shoulder screws which are steel. INCLUDES: Two steering bellcranks Four 5x8x2.5mm bellcrank bushings. Two...