Traxxas

This is the set of Traxxas Long GTR Shock Springs with 0.892 Blue Compression Rate. FEATURES Steel construction, white in...

.

.

FEATURES: Made of black plastic. INCLUDES: One skid plate SPECS: Length: 3-11/16" (68mm) Width: 5-3/4" (146mm) Height: 1-1/8" (29mm)

FEATURES: Foam construction, black in color Installs on chassis underneath front of body to help absorb frontal impacts INCLUDES: Body Bumper Foam for the Traxxas 1/10 scale Rally Car SPECS: Width: 7...

FEATURES: Made of black plastic INCLUDES: One bulkhead SPECS: Length: 3" (76mm) Width: 2-13/16" (71mm) Height: 2" (51mm)

FEATURES: Made of black plastic. INCLUDES: One battery hold-down One tall front hold-down retainer One tall rear hold-down retainer SPECS: hold-down, length: 7-5/8" (194mm) width: 1-1/4" (32mm)...

FEATURES: Made of black plastic INCLUDES: Three different pieces COMMENTS: This battery holder is a replacement part.

FEATURES: Plastic construction, black in color INCLUDES: Upper and lower Case Halves with Wire Cover Gasket Two Foam Pads Two 3x12mm Button Head Cap Screws Two 3x6mm Button Head Cap Screws Two 2...

  Slash 4X4 Low-CG (Low Center of Gravity) Conversion Kit Everything to convert your Slash 4X4 Performance-proven by the Slash 4X4 Ultimate and 1/10 Rally, the Traxxas Low-CG chassis is...

FEATURES Constructed of plastic, black in color INCLUDES Front and Rear Body Mounts

FEATURES: Blue aluminum construction          Holds 550 size motor in placeINCLUDES: One motor plate

.

FEATURES: Foam construction          Black in colorINCLUDES: One foam body bumper

FEATURES: GTR shock springs for the 1/16 Summit          Steel constructionINCLUDES: Two SpringsREQUIRES: Installation onto shocksSPECS:   ...

.

FEATURES: Nylon construction          White in colorINCLUDES: One Wing          Decal SheetREQUIRES:...

FEATURES: Nylon construction          Black in colorINCLUDES: One Wing Mount          Two 2.9x9.75mm Button...

This is the Traxxas Titan 380 18 Turn Brushed Motor.FEATURES: 18 turn, used in Traxxas 1/16 scale vehiclesINCLUDES: One Titan 380 Motor with 4mm bullet connectors

FEATURES: Steel construction, black in colorINCLUDES: Two Drive Cups

.

FEATURES: Nylon construction          Red in colorINCLUDES: Two Front and two Rear Toe Links          Eight...

FEATURES: Blue rubber sealed          May also be used in any vehicle where this size bearing is requiredINCLUDES: Two Ball BearingsREQUIRES: Installation...

Fine-tune your model for high-grip racing with this track-tested sway bar set. Sway bars reduce chassis roll and increase corner speed on high-traction surfaces—perfect for...

FEATURES: Steel construction Black and silver for soft and hard INCLUDES: 2 front sway bars 2 rear sway bars REQUIRES: Installation on vehicle

Bearing adapter, 6160-T6 aluminum (blue-anodized) (1)/10x15x4mm ball bearing (blue rubber sealed) (1) (for slipper shaft) FEATURES: 6061-T6 anodized blue aluminum construction Steel 10x15x4mm ball...

FEATURES: 6061-T6 anodized blue aluminum construction Steel 10x15x4mm ball bearing with blue rubber seal Used on slipper shaft INCLUDES: One aluminum adapter One 10x15x4mm ball bearing REQUIRES:...

The machined Aluminum Motor Plate offers rock-solid mounting security for major horsepower in all Slash 4X4 and 1/10 Rally models. Brilliant anodizing with bright aluminum highlights show off the...

FEATURES: Hardened steel construction INCLUDES: One Drive Hub One Screw Pin REQUIRES: Installation on the vehicle SPECS: Length: 19mm (0.75") Diameter: 12mm (0.47")

FEATURES: Nylon and steel construction INCLUDES: One Center Rear Drive Hub REQUIRES: Installation in drive assembly

FEATURES: Black nylon, aluminum and steel construction INCLUDES: Two housing pieces Two X-ring gaskets Two ring gear gaskets/bushings Two 5x10x0.5mm TW Four 2.5x8mm CCS REQUIRES: Installing all diff...

FEATURES: Steel construction Replaces worn or damaged center differential gears INCLUDES: Two Output Gears Two Spider Gears One Spider Gear Shaft REQUIRES: Diassembly of differential

FEATURES: Hardened plastic construction Black in color INCLUDES: Two rear differential housing halves REQUIRES: Installation around diff components

FEATURES: Steel construction INCLUDES: One Differential Ring Gear One Differential Pinion Gear REQUIRES: Installation in differential assembly SPECS: Pinion Gear: Tooth: 13T Inner Diameter: 5mm (0...

Crystal-clear plastic gear cover is just as durable as the stock cover, but lets you see the gear mesh for easy, no-tool inspection. It's also the perfect accessory for showing off the optional...

FEATURES: Nylon construction Black in color INCLUDES: One Gear Cover One motor wire hold down REQUIRES: Installation on the vehicle

.

FEATURES: Mounted BG Goodrich tires with foams on Split Spoke Satin chrome, black beadlock style wheels in plastic INCLUDES: Two mounted BF Goodrich Mud Terrain T/A KM2 tires with foams Two Split...

Tires & wheels, assembled, glued (SCT Split-Spoke black chrome beadlock style wheels, BFGoodrich® Mud-Terrain™ T/A® KM2 ultra-soft S1 compound off-road racing tires, foam inserts) (2) (4WD f/r,...

FEATURES: Fits two wheel and four wheel drive 1/10 scale Traxxas Slash Off-road rubber treaded tires Dual profile (inner diameters of 2.2" (56mm) and 3.0" (76mm) SCT split-spoke chrome with red...

FEATURES: Fits front and rear of the 4wd 1/10 scale Traxxas Slash and the front of the 2wd Slash Off-road rubber treaded tires Dual profile (inner diameters of 2.2" (56mm) and 3.0" (76mm) SCT...

FEATURES: Fits front and rear of the Slash 4x4 and the rear of the 2 wheel drive Slash Red colored wheel with chrome finish spokes Dual profile beadlock style INCLUDES: Two SCT Split Spoke Wheels in...

FEATURES: Fits two wheel and four wheel drive 1/10 scale Traxxas Slash Off-road rubber treaded tires Dual profile (inner diameters of 2.2" (56mm) and 3.0" (76mm) INCLUDES: Two Mud Terrain T/A KM2...

FEATURES: Ultra-soft S1 off-road racing compound Dual profile Gray foam inserts INCLUDES: Two Dual Profile 4.3x1.7-2.2/3.0" Kuhmo Tires with Inserts REQUIRES: 2.2" wheels SPECS: Outer Diameter: 4.3"...

FEATURES: Rubber construction Dual profile Foam inserts INCLUDES: Two Dual Profile 4.3x1.7-2.2/3.0" Kuhmo Tires Two Foam Inserts REQUIRES: 2.2" wheels SPECS: Outer Diameter: 110mm (4.3") Inner...

FEATURES: Allows XO-1 Supercar type steel-splined driveshafts with 6mm axles to be used on the 1/10 scale Traxxas Slash 4x4, Rally 4x4, and Stampede 4x4 Heavy duty machined aluminum construction,...

FEATURES: Steel construction, white in color Blue firmness rating +20% progressive compression INCLUDES: Two Blue Rate Rear Shock Springs for the Traxxas Slash REQUIRES: Installing over outside of...

FEATURES: Steel construction, white in color Pink firmness rating +10% progressive compression INCLUDES: Two Pink Rate Rear Shock Springs for the Traxxas Slash REQUIRES: Installing over outside of...

FEATURES: Steel construction, white in color Green firmness rating -10% progressive compression INCLUDES: Two Green Rate Rear Shock Springs for the Traxxas Slash REQUIRES: Installing over outside of...

FEATURES: Steel construction, white in color Orange firmness rating -20% progressive compression INCLUDES: Two Orange Rate Rear Shock Springs for the Traxxas Slash REQUIRES: Installing over outside...

FEATURES: Steel construction, white in color Blue firmness rating +20% progressive compression INCLUDES: Two Blue Rate Rear Shock Springs for the Traxxas Slash REQUIRES: Installing over outside of...

FEATURES: Steel construction, white in color Pink firmness rating +10% progressive compression INCLUDES: Two Pink Rate Front Shock Springs for the Traxxas Slash REQUIRES: Installing over outside of...

FEATURES: Steel construction, white in color Green firmness rating -10% progressive compression INCLUDES: Two Green Rate Front Shock Springs for the Traxxas Slash REQUIRES: Installing over outside of...

FEATURES: Steel construction, white in color Orange firmness rating -20% progressive compression INCLUDES: Two Orange Rate Front Shock Springs for the Traxxas Slash REQUIRES: Installing over outside...

Ideal for extra-high-power brushless setups (such as the optional Castle Creations Mamba Monster system), this solid-aluminum Motor Mount is extremely rigid for total power transfer. And extremely...

FEATURES: Hardened plastic construction          Black in colorINCLUDES: One motor mount assembled with a 3x6mm flat head machine...

FEATURES: White in color Steel construction Progressive rate INCLUDES: Two White Progressive Rate Shock Springs REQUIRES: Installation on the vehicle SPECS: Length: 65mm (2.6") Outer Diameter: 18.6mm...

Traxxas' 17mm Hex Adapters make it easy to install a wide range of wheel and tire combinations on your Traxxas vehicle. Installation is simple and can be done in less than 15 minutes using the...

Driveshaft, center, 6061-T6 aluminum (green-anodized)Accessory part for these models:Ford Fiesta® ST RallySlash 4X4 PlatinumSlash 4X4 UltimateSlash 4X4 VXLSlash 4X4

FEATURES: Hollow aluminum construction Anodized blue in color INCLUDES: One Aluminum Center Driveshaft REQUIRES: Installation on the vehicle SPECS: Length: 215mm (8.5") Diameter: 8.3mm (0.33")

Fits Continued: 1/10 Nitro Slash FEATURES: Aluminum construction INCLUDES: 2 rear stub axles 2 pins REQUIRES: Installation on vehicle

Traxxas Steel Constant Velocity Shafts offer the ultimate in torque handling and efficient power transfer. The outer U-joints are lubricated and sealed by a rubber boot for maximum protection against...

FEATURES: Black plastic and steel construction INCLUDES: Front driveshaft assembly Screw pin REQUIRES: Installation on vehicle  

FEATURES: Black plastic and steel construction INCLUDES: 2 external splined half shafts 2 internal splined half shafts 4 metal u-joints REQUIRES: Installation on vehicle

.

FEATURES: Composite nylon construction Replaces a worn or damaged bellcrank set May also be installed on the Traxxas Rustler, Bandit and 2WD Slash models (assembled in different configurations...

FEATURES: Clear nylon construction INCLUDES: One Center Driveshaft Cover REQUIRES: Installation over driveshaft SPECS: Length: 210mm (8.3") Width: 15mm (0.59")

Record your Slash 4X4 adventures and share them online with the Traxxas R/C Hero On Board Video Camera! Mounting the camera (not included) is easy using this high-strength fiberglass bracket. It...

Insist on the only aluminum shock towers that are by Traxxas, for Traxxas. These precision-machined towers add extra strength and anodized style without compromising Slash 4X4's race-bred geometry...

FEATURES: Hardened plastic construction Black in color INCLUDES: One front shock tower REQUIRES: Installation on chassis SPECS: Length: 71mm (2.80") Width: 49mm (1.93")  

Precision-machined for total steering accuracy and bulletproof strength, Traxxas Aluminum Steering Blocks further refine Slash 4X4's razor-sharp handling. Solid 6061 aluminum construction guarantees...

Precision-machined for total steering accuracy and bulletproof strength, Traxxas Aluminum Steering Blocks further refine Slash 4X4's razor-sharp handling. Solid 6061 aluminum construction guarantees...

FEATURES: Hardened plastic construction Black in color INCLUDES: Two steering blocks REQUIRES: Installation on steering assembly SPECS: Length: 35mm (1.38") Width: 32mm (1.26")

FEATURES: Durable steel construction Silver in color INCLUDES: Four 51.5mm pins Four 30mm pins

This unique C-Hub design is already Traxxas Tough; this artfully machined aluminum version is stronger still, and preserves the carefully engineered steering and suspension geometry for track-ready...

This unique C-Hub design is already Traxxas Tough; this artfully machined aluminum version is stronger still, and preserves the carefully engineered steering and suspension geometry for track-ready...

Caster blocks (c-hubs), 6061-T6 aluminum (green-anodized), left & rightAccessory part for these models:Ford Fiesta® ST RallySlash 4X4 PlatinumSlash 4X4 UltimateSlash 4X4 VXLSlash 4X4Stampede 4X4...

FEATURES: Hardened plastic construction Black in color INCLUDES: One left caster block One right caster block REQUIRES: Installation on Slash SPECS: Length: 49mm (1.93") Width: 29.5mm (1.16")

FEATURES: Hardened plastic construction Black in color INCLUDES: One rear bulkhead

FEATURES: Black plastic construction INCLUDES: 2 Ouput yokes 2 screw pins REQUIRES: Installation on vehicle

FEATURES: Aluminum construction, red in color INCLUDES: Two Front and Rear Bulkhead Tie Bars

FEATURES: Aluminum construction Anodized blue in color INCLUDES: Two bulkhead tie bars (front and rear)

FEATURES: Nylon construction Gray in color INCLUDES: One Chassis REQUIRES: Installation of car components SPECS: Length: 310mm (12.2") Width: 180mm (7.1") Thickness: 2.5mm (0.10")

Expand your competitive edge! The optional Center Differential transfers power to the front and rear differentials independently for smooth power delivery in rough conditions and maximum corner speed...

FEATURES: Four clear LED lights in chrome finish plastic housings INCLUDES: Four Lights with Housings, Wiring, Mounting Hardware and Instructions SPECS: Housing Diameter: 0.68" (17.3mm)

Tires and wheels, assembled, glued 2.8" (All-Star chrome wheels, Maxx® tires, foam inserts) (2)Replacement part for these models:Stampede 4X4Accessory part for these models:Rustler 4X4Bigfoot® No. 1...

FEATURES: Constant velocity steel splined construction INCLUDES: Two Diff Output Shafts

FEATURES: Rebuilds front and rear driveshafts INCLUDES: Tube of Grease, six Silicone Seals and ten Pins COMMENTS: Does not include half shafts

Driveshaft, center, 6061-T6 aluminum (green-anodized)Accessory part for these models:Stampede 4X4 Unassembled KitStampede 4x4 VXLStampede 4x4Telluride 4x4

FEATURES: 6061-T6 Aluminum construction Anodized blue in color INCLUDES: One aluminum center drive shaft REQUIRES: Installation on to vehicle SPECS: Length: 165.1mm (6.5") Outer Diameter: 8.5mm (0...

FEATURES: Made of steel INCLUDES: One stub axle SPECS: Length: 36.5mm (23/16") Diameter: 11.7mm (15/32") Threaded part of shaft, length: 9.4mm (3/8") diameter: 3.9mm (5/32")

FEATURES: Made of steel INCLUDES: One stub axle SPECS: Length: 38mm Diameter, bell end: 12mm (1/2") shaft: 5.0mm (3/16") threads: 3.9mm (5/32") Length of thread: 9.3mm (3/8")

FEATURES: Hardened steel construction INCLUDES: Internal Splined Half Shaft

FEATURES: Polished steel construction Externally splined INCLUDES: One Constant Velocity Half Shaft

FEATURES: Constructed of clear plastic INCLUDES: One rear shaft cover REQUIRES: Installation

.

FEATURES: Black plastic construction INCLUDES: Rear suspension arm guards (2) Guard spacers(2) Hallow Balls (2) 3x16mm BCS (2) REQUIRES: Installation on vehicle

FEATURES: Composite plastic construction Black in color INCLUDES: Two front suspension arm guards Two guard spacers Two hollow balls Eight 3x16mm button head cap screws REQUIRES: Installation onto...

FEATURES: Composite construction Allows installation of taller multi-cell batteries INCLUDES: Battery Hold Down with metal Post and Body Clip REQUIRES: Fastening to chassis

FEATURES: Composite construction Holds stock 7-cell battery supplied with vehicle INCLUDES: Two battery Hold Down sections with metal Post and Body Clip REQUIRES: Fastening to chassis COMMENTS: Also...