Traxxas

  This is the Center Gear Box (Transmisssion) (Front & Rear halves) for the REVO from Traxxas.   FEATURES Durable black nylon construction   INCLUDES One center gear...

FEATURES: Durable Black plastic construction INCLUDES: One left suspension arm One right suspension arm REQUIRES: screw pins for installing SPECS: Length: 3-5/8"

.

.

FEATURES: Silver metal construction Round head machine screws Phillips drive INCLUDES: Six Screws. SPECS: Length: 8mm Diameter: 2.6mm

FEATURES: Steel construction Rubber sealed INCLUDES: Two Ball Bearings REQUIRES: Installation on the vehicle SPECS: Outer Diameter: 27mm (1.06") Inner Diameter: 20mm (0.79") Width: 4mm (0.16")

FEATURES: Steel construction, silver in color Used on the Traxxas Revo monster truck, can also be used in any application where a 2x6mm roundhead self tapping screw is required INCLUDES: Six 2x6mm...

.

 

FEATURES: Nylon Construction          Black in Color   INCLUDES: One Spur Gear

Fits Continued: 1/10 Ford Raptor / Rally VXL / Slash R.G.D. / Nitro 4-Tec / Nitro Slash / Nitro Sport / Nitro Stampede / T-Maxx / Nitro Rustler / T-Maxx Classic FEATURES: Black nylon rod ends Steel...

FEATURES: Black Steel springs INCLUDES: Two Springs REQUIRES: Installing on Traxxas Street Sport Shocks SPECS: Length: 25.4 mm (1") Diameter: 18.6 mm (0.731")

.

.

FEATURES: Nylon Construction Black in Color INCLUDES: One Left Rear Suspension Arm One Right Rear Suspension Arm REQUIRES: Assembly onto Vehicle

FEATURES: Plastic construction Gray in color Progressive 1, Low Rate INCLUDES: One Left/Front Upper Rocker Arm One Left/Front Lower Rocker Arm One Right/Front Upper Rocker Arm One Right/Front Lower...

FEATURES: Black Plastic Construction INCLUDES: Two Wedges REQUIRES: Traxxas 4-TEC SPECS: Length: 20mm (.787") Width: 7mm (.275") COMMENTS: None

.

.

.

These are the 4x35mm Button Head Machine Screws for the Traxxas X-Maxx Monster Truck, TRAD75**. FEATURES Steel construction Secures...

.

FEATURES: Nylon and steel construction INCLUDES: 2 Rod ends 2 Ball studs 2 Hollow balls REQUIRES: Installation on front suspension

FEATURES: Nylon Construction          Black in Color   INCLUDES: One Spur Gear

Traxxas Steel Constant Velocity Shafts offer the ultimate in torque handling and efficient power transfer. The outer U-joints are lubricated and sealed by a rubber boot for maximum protection against...

FEATURES: Replaces worn bearings Constructed of steel INCLUDES: Two 6x12x4mm Ball Bearings for the Traxxas T-Maxx Monster Truck REQUIRES: Installing two bearings in each axle carrier (4932) and two...

This is the Main Diff with Steel Ring Gear from Traxxas for the Bandit, Stampede and Rustler VXL series. Includes: Main diff with steel ring gear Side cover plate Screws Instructions Requires:...

FEATURES Hardened steel construction   INCLUDES Pinion Gear for the Front Differential

FEATURES: Nylon construction Black in color INCLUDES: One Left and Right 25° Caster Blocks One Left and Right 25° Steering Blocks REQUIRES: Assembly onto Vehicle

.

Fits Continued: 1/10 Maximum Destruction / Monster Mutt / Ford Raptor / Slash R.G.D. / Nitro Jato 3.3 / Nitro 4-Tec / Nitro Slash / Nitro Sport / Nitro Stampede / Nitro Rustler FEATURES: Aluminum...

FEATURES: Steel construction   INCLUDES: One Pinion Gear with set screw

FEATURES: Steel construction Nylon locking insert Silver in color INCLUDES: Twelve 2.5mm nuts REQUIRES: 5mm open-end or four-way wrench for assembly. SPECS: Nut Hex size: 5mm (.20") Internal thread...

This is an optional Traxxas "Long" Temperature & Voltage Sensor. Temperature data is critical to monitoring performance, gauging the effects of changes, and preventing overheating. The...

This is a tube of white lithium grease from Traxxas. This is used to lubricate gears and differential components.

FEATURES: 1.4 lb/in tension Red coating INCLUDES: Two Shock Springs REQUIRES: Assembly onto the Traxxas Slayer Shocks SPECS: Length: 51mm (2") Diameter: 21mm (0.83")

FEATURES: Thicker steel construction. INCLUDES: Two turnbuckles with pre-installed rod ends and balls. REQUIRES: Nothing. These are direct replacement rods. SPECS: Length: 118mm (4.65") Thickness:...

#5339 Insert, threaded steel (replacement inserts for TUBES) (includes (1) left and (1) right threaded insert) Insert, threaded steel (replacement inserts for TUBES) (includes (1) left and (1) right...

FEATURES: Red in color (small gold square indicates spring type) Metal construction INCLUDES: 2 springs SPECS: Length: 1-11/16" (43mm) Inside diameter: 11/16" (17mm) Outside diameter: 7/8" (22mm)...

FEATURES: Replaces damaged or worn clutch bells Constructed of steel INCLUDES: One Forward and Reverse Clutch Bell for the Traxxas T-Maxx REQUIRES: Diassembly of transmission and installing on output...

.

.

.

.

**This conversion kit requires a 3-channel transmitter to shift gears.** FEATURES: Everything needed to convert the E-Revo transmission to two speed shifting Provides more torque for climbing and...

.

.

.

FEATURES: Durable steel construction INCLUDES: Two 13 Tooth Output Gear Shafts Two 13 Tooth Spider Gears One Spider Shaft One 6x10x0.5mm washer REQUIRES: Assembly into differential COMMENTS: This set...

This is thrust bearing lube that can be used on all the Traxxas kits as well asmost other kits on the market.  It is to be used on thrust bearings, and not onball diffs or planetary diffs. ...

FEATURES: Ten spoke chrome plated plastic construction, spokes are in groups of two Fits front or rear of vehicle INCLUDES: Two optional Traxxas Split Spoke 3.8" Chrome Wheels w/17mm Hub...

FEATURES: Hard anodized aluminum Machine thread INCLUDES: Four threaded ball studs REQUIRES:2.5mm hex driver SPECS: Length:14mm(.56") Ball Diameter:6mm Threaded Diameter:3mm

FEATURES: Metal Construction Silver in Color Bent for Easy Removal INCLUDES: Ten Bent Silver Metal Body Clips REQUIRES: Assembly onto Vehicle

FEATURES: Nylon construction Black in color INCLUDES: One Front Bumper One Bumper Mount Two 3x25mm Button Cap Screws Two 4x10mm Button Cap Screws REQUIRES: Installation on the vehicle

FEATURES: Nylon construction          Black in color          Fits left or rightINCLUDES: Two Internal...

FEATURES: Nylon Construction Silver Bumper and Black Mount INCLUDES: One Silver Nylon Front Bumper One Black Nylon Front Bumper Mount Two 3mm x 25mm Cap Hex Head Machine Thread Screws Two 4mm x 10mm...

FEATURES: Nylon construction Black in color INCLUDES: One Front Bumper REQUIRES: Assembly onto vehicle  

FEATURES: Spring Steel Construction Red Outer Nylon Coating Yellow 2.6 tension rating INCLUDES: Two Red 2.6 Springs for the Traxxas GTR Shocks used on the Revo REQUIRES: Nothing SPECS: Length: 1.8"...

This is an optional Traxxas "Short" Temperature & Voltage Sensor. Temperature data is critical to monitoring performance, gauging the effects of changes, and preventing overheating. The...

FEATURES: Steel construction          Black in colorINCLUDES: Six Countersunk Machine Flat Head ScrewsREQUIRES: Installation on the...

FEATURES: Black chrome wheels INCLUDES: Two All-Star 2.8" rear black chrome wheels REQUIRES: Installation on the vehicle SPECS: Overall Diameter: 2.8" (71mm) Width: 1.92" (49mm)  

FEATURES: Nylon construction White in color INCLUDES: Forward and Reverse Primary Gears One Screw Pin One Pin and Clip REQUIRES: Installation on the vehicle

Fits Continued: 1/10 Slash R.G.D. / Nitro 4-Tec / Nitro Slash / Nitro Sport / Nitro Stampede / T-Maxx / Nitro Rustler / T-Maxx Classic FEATURES: Nylon construction Helps prevent the body mount hole...

.

FEATURES: Seals receiver box from dirt and moisture INCLUDES: Silicone O-Ring Two sections of Foam Tape Silicone Grease Instruction Sheet

.

FEATURES: Metal bearing construction Blue rubber dirt shields INCLUDES: (2) 5X10mm ball bearings, Part #5115 SPECS: Inside diameter: 3/16" (5mm) Outside diameter: 3/8" (10mm) Width: 5/32" (4mm)

FEATURES: Hardened steel construction INCLUDES: One differential output gear for the Revo 3.3 REQUIRES: Installation into rear of center diff with rear brake kit. SPECS: Length:1.91"(48.66mm) Shaft...

FEATURES: Nylon construction          Blue in colorINCLUDES: One Servo Case (Top, Middle, and Bottom...

.

 

.

.

FEATURES: Needle/Roller Bearing design Steel construction INCLUDES: Two Needle Roller Bearings REQUIRES: Nothing SPECS: Bearing size: 6x10mm Thickness: 8mm COMMENTS: These bearings are installed so...

 

.

.

FEATURES: Durable black nylon construction INCLUDES: One upper RIGHT FRONT suspension arm One lower RIGHT FRONT suspension arm REQUIRES: Suspension pin set to attach to bulkhead SPECS: UPPER LOWER...

FEATURES: Metal construction White in color Silver weight rating 1.2 INCLUDES: Two Super Shock Springs Silver 1.2 REQUIRES: Assembly onto Vehicle

FEATURES: nylon construction, used to secure wires INCLUDES: 6 tie wraps SPECIFICATIONS: 1/8" wide, 6" long REQUIRES: nothing, this is a replacement part

FEATURES: Black plastic construction INCLUDES: Center front half shafts Part #5455 Center rear half shafts #5455 SPECS: Approx. length front: 1-7/8" (41mm) Approx. length rear: 2-5/8" (61mm)

 This is the Lightweight Output/Idler Gear Shaft for the Traxxas E-Maxx. This shaft is located in the gearbox between the Drive Dog, key #3986 (TRAC3986) and the #3984 Output Gear (TRAC3984)...

This is for the Front & Rear Linkage Sway Bar Sets for the Slash 4x4 and Stampede 4x4 from Traxxas.     FEATURES Nylon and steel...

FEATURES: Nylon Construction          Black in Color   INCLUDES: One Spur Gear

FEATURES: Restores proper performance to worn Velineon motorsINCLUDES: Two 4x9x4mm Ball Bearings          Two 2x6mm Countersunk...

The Maxx wheelie bar has 4 snap-in adjustment positions that allow you to choose how extreme you want your action to be. The unique patent-pending design allows it to be easily removed in situations...

FEATURES: Nylon construction Gray in color Molded Composite INCLUDES: Two Molded Composite GTR Shock Bodies REQUIRES: Assembly onto Vehicle

FEATURES: Steel construction          Constant velocityINCLUDES: Four Driveshafts

FEATURES: Machined aluminum construction INCLUDES: Two Aluminum Rear Stub Axle Carriers Two 3x3mm Set Screws Two 3x12mm Flat Phillips Head Screws Two 3x31.5mm Pins Six 6mm E-Clips

Includes: - Main Frame (2) - Battery Holder (1) - Canopy Mounting Posts (2) - Screws (2)

Fits Continued: 1/10 Maximum Destruction / Monster Mutt / Ford Raptor / Rally VXL / Slash R.G.D. / Nitro Jato 3.3 / Nitro 4-Tec / Nitro Slash / Nitro Sport / Nitro Stampede / Nitro Rustler FEATURES:...

FEATURES: Steel construction Progressive rate White in color INCLUDES: Two Front White Shock Springs REQUIRES: Installation on the shocks SPECS: Length: 47mm (1.9") Inner Diameter: 15.5mm (0.61")...

.

FEATURES: Plastic shift fork construction Metal shift fork shaft Shift fork plastic is black in color Preassembled INCLUDES: One shift fork and shaft, Part #5389 REQUIRES: Installation on the Traxxas...

FEATURES: Three bar ratings: soft, intermediate, and firm Color coded: soft is silver, intermediate is white, and firm is black INCLUDES: Three sway bars

FEATURES: Made of black plastic, these are mounted to the side of the car to protect agains side impacts. INCLUDES: Two nerf bars SPECS: Length: 5-1/2" Width: 1-7/8" Height: 2-1/4"

FEATURES: Nylon construction Black in color INCLUDES: One Pull Ring One Fuel Tank Cap One Fuel Line Pinch Clip REQUIRES: Assembly onto Vehicle

FEATURES: Nylon and metal construction Black and silver in color INCLUDES: Two 3x70mm assembled front turnbuckles with rod ends, hollow balls and ball studs REQUIRES: The remaining parts of the sway...

This is the High-Torque Digital Waterproof Steering Servo for the Traxxas X-Maxx Monster Truck     FEATURES Ball bearing...

FEATURES: Steel construction          Black in colorINCLUDES: Six Countersunk Machine ScrewsREQUIRES: Installation on the vehicleSPECS:   ...