Traxxas

FEATURES: Steel construction          Black in colorINCLUDES: Six Countersunk Machine Flat Head ScrewsREQUIRES: Installation on the...

FEATURES: Black chrome wheels INCLUDES: Two All-Star 2.8" rear black chrome wheels REQUIRES: Installation on the vehicle SPECS: Overall Diameter: 2.8" (71mm) Width: 1.92" (49mm)  

FEATURES: Nylon construction White in color INCLUDES: Forward and Reverse Primary Gears One Screw Pin One Pin and Clip REQUIRES: Installation on the vehicle

Fits Continued: 1/10 Slash R.G.D. / Nitro 4-Tec / Nitro Slash / Nitro Sport / Nitro Stampede / T-Maxx / Nitro Rustler / T-Maxx Classic FEATURES: Nylon construction Helps prevent the body mount hole...

.

FEATURES: Seals receiver box from dirt and moisture INCLUDES: Silicone O-Ring Two sections of Foam Tape Silicone Grease Instruction Sheet

.

FEATURES: Metal bearing construction Blue rubber dirt shields INCLUDES: (2) 5X10mm ball bearings, Part #5115 SPECS: Inside diameter: 3/16" (5mm) Outside diameter: 3/8" (10mm) Width: 5/32" (4mm)

FEATURES: Hardened steel construction INCLUDES: One differential output gear for the Revo 3.3 REQUIRES: Installation into rear of center diff with rear brake kit. SPECS: Length:1.91"(48.66mm) Shaft...

FEATURES: Nylon construction          Blue in colorINCLUDES: One Servo Case (Top, Middle, and Bottom...

.

 

.

.

FEATURES: Needle/Roller Bearing design Steel construction INCLUDES: Two Needle Roller Bearings REQUIRES: Nothing SPECS: Bearing size: 6x10mm Thickness: 8mm COMMENTS: These bearings are installed so...

 

.

.

FEATURES: Durable black nylon construction INCLUDES: One upper RIGHT FRONT suspension arm One lower RIGHT FRONT suspension arm REQUIRES: Suspension pin set to attach to bulkhead SPECS: UPPER LOWER...

FEATURES: Metal construction White in color Silver weight rating 1.2 INCLUDES: Two Super Shock Springs Silver 1.2 REQUIRES: Assembly onto Vehicle

FEATURES: nylon construction, used to secure wires INCLUDES: 6 tie wraps SPECIFICATIONS: 1/8" wide, 6" long REQUIRES: nothing, this is a replacement part

FEATURES: Black plastic construction INCLUDES: Center front half shafts Part #5455 Center rear half shafts #5455 SPECS: Approx. length front: 1-7/8" (41mm) Approx. length rear: 2-5/8" (61mm)

 This is the Lightweight Output/Idler Gear Shaft for the Traxxas E-Maxx. This shaft is located in the gearbox between the Drive Dog, key #3986 (TRAC3986) and the #3984 Output Gear (TRAC3984)...

This is for the Front & Rear Linkage Sway Bar Sets for the Slash 4x4 and Stampede 4x4 from Traxxas.     FEATURES Nylon and steel...

FEATURES: Nylon Construction          Black in Color   INCLUDES: One Spur Gear

FEATURES: Restores proper performance to worn Velineon motorsINCLUDES: Two 4x9x4mm Ball Bearings          Two 2x6mm Countersunk...

The Maxx wheelie bar has 4 snap-in adjustment positions that allow you to choose how extreme you want your action to be. The unique patent-pending design allows it to be easily removed in situations...

FEATURES: Nylon construction Gray in color Molded Composite INCLUDES: Two Molded Composite GTR Shock Bodies REQUIRES: Assembly onto Vehicle

FEATURES: Steel construction          Constant velocityINCLUDES: Four Driveshafts

FEATURES: Machined aluminum construction INCLUDES: Two Aluminum Rear Stub Axle Carriers Two 3x3mm Set Screws Two 3x12mm Flat Phillips Head Screws Two 3x31.5mm Pins Six 6mm E-Clips

Includes: - Main Frame (2) - Battery Holder (1) - Canopy Mounting Posts (2) - Screws (2)

Fits Continued: 1/10 Maximum Destruction / Monster Mutt / Ford Raptor / Rally VXL / Slash R.G.D. / Nitro Jato 3.3 / Nitro 4-Tec / Nitro Slash / Nitro Sport / Nitro Stampede / Nitro Rustler FEATURES:...

FEATURES: Steel construction Progressive rate White in color INCLUDES: Two Front White Shock Springs REQUIRES: Installation on the shocks SPECS: Length: 47mm (1.9") Inner Diameter: 15.5mm (0.61")...

.

FEATURES: Plastic shift fork construction Metal shift fork shaft Shift fork plastic is black in color Preassembled INCLUDES: One shift fork and shaft, Part #5389 REQUIRES: Installation on the Traxxas...

FEATURES: Three bar ratings: soft, intermediate, and firm Color coded: soft is silver, intermediate is white, and firm is black INCLUDES: Three sway bars

FEATURES: Made of black plastic, these are mounted to the side of the car to protect agains side impacts. INCLUDES: Two nerf bars SPECS: Length: 5-1/2" Width: 1-7/8" Height: 2-1/4"

FEATURES: Nylon construction Black in color INCLUDES: One Pull Ring One Fuel Tank Cap One Fuel Line Pinch Clip REQUIRES: Assembly onto Vehicle

FEATURES: Nylon and metal construction Black and silver in color INCLUDES: Two 3x70mm assembled front turnbuckles with rod ends, hollow balls and ball studs REQUIRES: The remaining parts of the sway...

FEATURES: Steel construction          Black in colorINCLUDES: Six Countersunk Machine ScrewsREQUIRES: Installation on the vehicleSPECS:   ...

FEATURES: Nylon construction Black in color INCLUDES: One Servo Arm for Airtronics, KO, and Sanwa One Servo Arm for JR One Servo Arm for Hitec Three Servo Case Mounts REQUIRES: Assembly onto Vehicle

FEATURES: Constructed of steel TiN coated for strength INCLUDES: Two TiN Coated GTR Shock Shafts

FEATURES: Steel construction Self tapping INCLUDES: Six 2.6 x 10mm Round Head Screws by Traxxas REQUIRES: Phillips head screwdriver SPECS: Length: 10mm Diameter: 2.6mm

FEATURES: Painted white Steel construction INCLUDES: Two springs SPECS: Length: 3.11" (79mm) Inside diameter: .61" (15mm) Outside diameter:.71" (18mm)

FEATURES: Anodized aluminum construction, red in color Black nylon ball ends INCLUDES: One 49mm red aluminum rear turnbuckle REQUIRES: Installation onto vehicle

.

FEATURES: Plastic Diff Gear INCLUDES: One 60T gear REQUIRES: Traxxas SRT (Stadium Race Truck) SPECS: Thickness: 8mm (0.31") Diameter: 33mm (1.30")  

FEATURES: One-piece rubber construction slips around mounting area of fuel tank to minimize tank vibration and foaming of fuel INCLUDES: Fuel Tank Vibration Cushion

his is the 7.2V NiMH 1800mAh Stick Battery Pack from Traxxas.FEATURES: Stick configuration          14-gauge...

FEATURES: Steel turnbuckle design 5.0mm diameter INCLUDES: Two front or rear toe links REQUIRES: Nothing. These are direct replacement parts. SPECS: Length: 5.1" (129mm)

.

FEATURES: Zinc finish Metal construction INCLUDES: (6) 3X28mm cap head screws (6) lock washers (6) washers (6) split washers SPECS: Length: 1-1/8" (28mm) Diameter: 1/8" (3mm)  

.

FEATURES: Steel construction   INCLUDES: One Pinion Gear with set screw

FEATURES: Plastic construction INCLUDES: EZ-Start Mount and Clamp with four 2.6x10mm Screws

FEATURES: Steel construction   INCLUDES: One Pinion Gear with set screw

FEATURES: Nylon and steel construction INCLUDES: 2 Rod ends 2 Ball studs 2 Hollow balls REQUIRES: Installation at rear suspension

FEATURES: Steel construction INCLUDES: Six 3x30mm Roundhead Machine Screws REQUIRES: Phillips screwdriver SPECS: Length: 30mm Diameter: 3mm

The unique patent-pending Traxxas adjustable wheelie bar features four position adjustment, plus it quickly and easily installs onto the rear of any electric Slash, Rustler, Stampede, and Bandit. The...

.

FEATURES: Ball bearings reduce friction and last longer than bushings. Double Shielded INCLUDES: One Ball Bearing REQUIRES: None, item is a stock part SPECS: Inner Diameter: 10mm Outer Diameter: 19mm...

FEATURES: Restores proper braking performance INCLUDES: Brake lever, mounting rod, spring, adjustment dial, rod guide bushing REQUIRES: Installing between steering servo and brake assembly

FEATURES: Nylon construction Black in color INCLUDES: Three Crossbraces Twelve 3x6mm Buttonhead Cap Screws Instruction sheet REQUIRES: Installation on the ExoCage

.

This is the Traxxas Power Cell 11.1V 4000mAh 25C 3S LiPo Battery.   FEATURES Semi rigid construction does not require a hard case and...

FEATURES: 1.6 lb/in tension Red coating INCLUDES: Two Shock Springs REQUIRES: Assembly onto the Traxxas Slayer Shocks SPECS: Length: 49mm (1.9") Diameter: 22mm (0.87")

FEATURES: Nylon construction          Red in colorINCLUDES: Four Pushrods          Eight Hollow Balls

.

FEATURES: Nylon construction           Black in color INCLUDES: One  Spur Gear

These are the 4x35mm Button Head Machine Screws for the Traxxas X-Maxx Monster Truck, TRAD75**. FEATURES Steel construction Secures...

.

FEATURES: Replaces stock gear shaft. Constructed of steel. INCLUDES: One gear shaft REQUIRES: Diassembly of gearbox and installing shaft between the spur gear and the primary gears.

.

.

This is an optional Traxxas "Long" RPM Sensor, and is intended for use with the Traxxas XO-1 1/7 Scale vehicle. To collect critical RPM data (Revolutions Per Minute), a "trigger magnet" is installed...

FEATURES: Plastic construction, black in color INCLUDES: Center half shafts (three internal splined and two external splined) REQUIRES: Installation on the vehicle SPECS: Diameter: 17.2mm (0.68")

.

FEATURES: Three bar ratings: soft, intermediate, and firm Color coded: soft is silver, intermediate is white, and firm is black INCLUDES: Three sway bars COMMENTS: These bars can be used to replace...

.

FEATURES: White plastic construction INCLUDES: One 40T 2nd speed gear One 13T/16T input gear One screw pin REQUIRES: Installation into Traxxas Revo.

FEATURES: Nylon construction          Black in colorINCLUDES: Front and Rear Gearbox Halves

FEATURES: Nylon construction Black in color INCLUDES: One Front Body Mount REQUIRES: Assembly onto Vehicle

FEATURES: Direct drop-in for the Revo 3.3, standard chassis Revos require the Accessory Rear Output Shaft, 9416 Transfers power to the front and rear differentials independently Sealed center...

FEATURES: Metal construction Black in color INCLUDES: Six 4mm x 18mm Countersunk Flathead Hex Screws REQUIRES: Assembly onto Vehicle

FEATURES: Fits front and rear of the Slash 4x4 and the rear of the 2 wheel drive Slash Red colored wheel with chrome finish spokes Dual profile beadlock style INCLUDES: Two SCT Split Spoke Wheels in...

These are the 5106A 15 x 24 x 5mm Ball Bearings for the Traxxas X-Maxx Monster Truck     FEATURES Steel construction with black rubber...

This is a pair of Assembled Traxxas SCT S1 Tires and 5-Spoke Wheels. FEATURES Fits the rear of 2WD short course trucks and the front and rear...

.

.

.

Fits Continued: 1/10 Nitro Sport / Nitro Stampede / Nitro Rustler FEATURES: Aluminum construction Gunmetal colored INCLUDES: One Big Bore Long Shock Body. REQUIRES: The remainder of the shock...

FEATURES: Painted white Steel construction INCLUDES: Two springs SPECS: Length: 2.46" (62mm) Inside diameter: .61" (15mm) Outside diameter: .71" (18mm)

.

.

FEATURES: Molded plastic construction INCLUDES: Front and Rear Drive Housing Halves

FEATURES: 2.8" All Star chrome wheels Talon tires and foam inserts INCLUDES: Two 2.8" mounted Talon tires, All Star chrome wheels and inserts REQUIRES: Installation on vehicle SPECS: Outside...

These are the 5106 15 x 24 x 5mm Ball Bearings for the Traxxas X-Maxx Monster Truck, TRAD75**. FEATURES Steel construction with blue...

A must have with the recent change to mostly only DC chargers from Traxxas.  Designed specifically for use with the Traxxas peak detecting DC fast chargers, the new AC to DC Adapter from...

FEATURES: Plastic construction Exo-carbon finish INCLUDES: Exo-Carbon Left and Right Suspension Arms for the Traxxas Jato REQUIRES: Installation on the Jato 3.3

FEATURES: Steel construction INCLUDES: Two stub axles REQUIRES: Nothing. These are direct replacement parts. SPECS: Length: 1.3" (33mm)