Power Supplies / Transformers

Everything you need to get started with Advanced Digitrax Command Control.Evolution Express is perfect for most home and club layouts wanting Duplex Radio control out of the box.It offers excellent speed control, prototypical consisting, the full range...

Everything you need to get started with Advanced Digitrax Command Control.Evolution Express is perfect for most home and club layouts. It offers excellent speed control, prototypical consisting, the full range of programming features and much more...

Supports up to 400 locomotives and throttles.On-board USB port.Three RJ12 LocoNet portsSupports SoundFX and sound decoder programming using Digitrax SoundLoader app over USB.5amp/8amp Booster with multi-scale capability.Built-in booster transponding...

This device provides extra current to the track for the control of an increased number of DCC locomotives on your HO, N, or On30 layout. Also appropriate for DCC decoder-equipped large scale locomotives.

The P1024 is a 24 Volt DC, 220-watt power supply with a US power cord.The power supply is suitable for use with the following NCE products: PB110 booster, PH10, PH10-R (10 amp systems).Note: The power supply includes an adapter with a 4-pin plug to...

The DT602D is our top-of-the-line, Duplex Radio Super Throttle.  The DT602D Advanced Super Throttle gives you direct control of two locos at a time with all the powerful features and flexibility serious model railroaders demand.The DT602D is...

Dual 3/5/8 Amp AutoReversing DCC BoosterUp to 16 Amps of power totalN, HO, & Large Scale Operations with Custom Voltage TrimLocoNet for easy plug ‘n play installation and system expansionEasy dip switch setupAuto resetting over temperature and short...

This power supply replaces the PS2012 to meet new efficiency requirements for DC power supplies. It delivers more power with less heat for more efficient operation. The 20 amp PS2012E regulated power supply can be used to operate up to 4 five amp...

Enjoy a fast way to get getting into DCC with the Bachmann E-Z Command Digital Command Control System. In partnership with Lenz, this system is both easy to use and affordable for novice and experienced hobbyists alike. E-Z Command allows modelers to...

BXP88 makes adding detection and transponding to your layout easier than ever.  No more complicated wiring!DCC Occupancy Detection supports up to 8 Detection Sections letting you know when equipped rolling stock is in a detection section on your...

Single 3/5/8 Amp AutoReversing DCC Booster (no command station capability)Up to 8 Amps of power totalN, HO, & Large Scale Operations with Custom Voltage TrimLocoNet for easy plug ‘n play installation and system expansionEasy dip switch setupAuto...

Adding the E-Z Command® Pro Box to your Dynamis® DCC System delivers more versatility to your railroad.The Dynamis® Pro Box allows:- the use of three additional wireless controllers (limit four)- use of additional wireless receivers- use of programming...

The Bachmann Large Scale Optical Auto-Reversing System brings automatic point-to-point train or streetcar operation to your railroad. Set up your system, add your train, and watch as it operates back and forth at your specified speed and stopping...

Walthers Layout Control System brings you a low-cost solution for easy turnout control for HO, N, Z, S, and O Scale layouts with this five-pack of Switch Machines! The Layout Control System is expandable at any time to grow with your layout, and can be...

Walthers Layout Control System brings you a low-cost solution for easy turnout control for HO, N, Z, S, and O Scale layouts with this five-pack of Switch Machines! The Layout Control System is expandable at any time to grow with your layout, and can be...

All plug-in connectors for simple and easy installation and service.User defined as 16 DS reporting addresses in 1 to 2000+ DS range.Easy setup with device Option Switches (OPSW)Powered by 2mm DC jack, 8V min to 22V max.Configured to operate with DCC...

4 Power Manager sub-districts.Upgraded replacement for PM42, fully encased.Fully connectorized installation.Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit management.Each DS supports Occupancy detection.Each DS...

This power supply is suitable for use with the following NCE products: PH5 (5 Amp systems)Note: For the older PowerPro 5 Amp NCE Systems or the PB105 booster, the customer should cut off the round connector, then strip the cable to expose the two wires...

Built tough for dependable service with the power to handle HO, S and O Scale equipment, the Walthers Controls DC Train Control makes a great addition to your layout with features that include:Improves locomotive performancePerfect for growing layouts...

This is a Power Pack and Speed Controller System from Bachmann Trains.Suitable for Ages 14 & Older.FEATURESFor use with DC-operated trains in N, HO and On30 scalePlug-in wiringPower indicator lightDirection control switchElectronic circuit...

FEATURES: Designed for use with the Bachmann® E-Z Command® System           Automatically switches polarity to allow reverse loop travel.         ...

This is the Bachmann Large Scale Power Pack & Speed Controller System.Suitable for Ages 14 & Older.FEATURESDesigned for use with Large Scale DC-operated trains(not DCC compatible)Plug-in wiringPower indicator lightDirection control...

The Kato Standard SX Power Pack is designed to keep your HO and N Scale standard DC trains running smoothly. Revised in 2024, this power pack is 100% compatible with all Unitrack electrical accessories and is an in-kind replacement for previous Kato...

DescriptionOutputs DC16V 2.1AIdeal for HO Gauge Layouts

Now you can power multiple accessories from one convenient power supply.Several accessories can be attached to each side of the power supply for up to 1 Amp total loadTypical 16V DC accessory attachments are approximately three per side (six total)for...

DescriptionOutputs DC13.5V 2.2AIdeal for N Gauge Layouts

Low-cost, High-sensitivity DCC block-occupancy detection.Adjustable resistance/current detection section (DS) trip threshold.8A capacity, suitable for all scales and track wiring configurations.Noise resistant and compatible with BDL168 sections.On-board...

New power supply for power injection to TCS panels and devices.WARNING:  This product is only intended for use with specific TCS products. TCS does not condone the use of this power supply for other uses than the following:LT-50 (Panel)LCC Throttle...

LocoNet Universal Panel and 3 Amp Z Scale Voltage Reducer6 LocoNet Jacks for use with all scalesReduces track voltage by 4 or 6 volts at 3 amps for safer Z Scale locomotive opreration with Digitrax equipment

.

The PS14 is a 300ma, 14 Volt power supply for powering Digitrax accessories like the UP5, BDL168, DS64, SE8C, LNRP, UR90, UR91 UR92 and others    Universal AC input 95-240V 50/60Hz  US 2 prong plug, in...

Add up to four Just Plug LED lights of your choice to a project quickly and easily. Regulate light brightness with individual dimmer controls. Add an optional Auxiliary Switch for convenient operation. Powering Your Light System You will need one...

FEATURES: Connects power pack to track and/or switch controller.          E-Z Track accessory for HO scale electric track.          Female and male ends.INCLUDES:...

This is the Auxilary Switch from the Just Plug Series by Woodland Scenics.  FEATURES Quickest and easiest way to add lights to any project Control lights with the flick of a switch Rocker style...

Gray Replacement Terminal Plug for lost or damaged plugs on Digitrax Command Stations and Boosters

The LT1 is included with all Digitrax Starter Sets. It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2 watt protection resistor. LT1 Features: Use...

.