Hot Racing

Hot Racing 1/10th scale rear bumper with tow shackle D-rings, LED light mounts, and winch mount for the Axial SCX10 FEATURES: - CNC machined solid billet aluminum construction - Feels very...

Optional Hot Racing Hardened Steel 32P 57T Spur Gear for use on the Arrma 1/10 2WD Specially make to handle brushless power FEATURES: Hardened steel construction Rugged 0.8...

Hot Racing 6x8mm aluminum standoff posts with M3 threads for miscellaneous applications such as suspension links, tie rods, or chassis cross membersFEATURES:- CNC machined 6061-T6 aluminum- Anodized...

Hot Racing hardened steel 16 tooth, 32 pitch pinion gear for motors with a 5mm shaftFEATURES:- CNC machined- Hardened steel to increased wear resistance and improve fatigue life- Nitrided to enhanced...

Hot Racing 21T, 0.6 module (~42P) steel pinion gear for 5mm or 1/8in motor shaftsFEATURES:- CNC machined steel with black Nitride finish- Heavy duty 4mm set screw- Long design for maximum motor shaft...

Hot Racing solid aluminum toe links (aka steering turnbuckle) for the Traxxas Maxx 4SFEATURES:- More rigid than factory plastic links for more predictable and consistent steering- CNC machined...

Hot Racing aluminum front steering blocks (left and right) for the 1/10 Traxxas MaxxFEATURES:- CNC machined aluminum- Anodized black- Machined chamfered edges- Laser etched lettering- Replaces...

Hot Racing aluminum Front Lower arms for the Losi 2WD Mini-T2.FEATURES:- CNC machined aluminum, anodized black.- Replaces worn stock black plastic Front Arm- Precision made for perfect bolt-on fitYOU...

This is the optional Adjustable Aluminum Motor Mount for the Losi 2WD Mini-T2FEATURES:Replaces stock Non-adjustable motor mount for a much wider range of Gear Ratio.Improves power transfer for...

Hot Racing aluminum heavy duty third member (i. e. center section, pumpkin) with oversized pinion support bearings for the 1/6 Losi Super Baja Rey and 1/6 Losi Super Rock ReyFEATURES:- CNC machined...

These are the Hot Racing Rear Axle Adapters for the Axial Yeti XL.     FEATURES CNC machined 6061 aluminum construction, black in...

This is the Hot Racing Hard Anodized Steel Center Gear Set for the Axial Yeti XL.     FEATURES CNC machined #45 steel...

These are the optional Hot-Racing One-Piece Wheel Hubs for the Axial Yeti, Wraith and AX10 vehicles with AR60 axles.     FEATURES CNC...

This is the optional Hot-Racing Wide Hex Hub Kit for the HPI Wheely King.     FEATURES CNC 6061-T6 Aluminum construction Widens wheel...

Hot Racing's aluminum 12mm to 17mm hex wheel hub adapters. These adapters are compatible with many 1/10th scale vehicles with factory 12mm hex hubs and allow the use of 17mm hex wheels, all while...

These are the optional Hot-Racing Long Slipper Clutch Pads for the Traxxas Rustler and Stampede.     FEATURES Constructed of hard...

These are the optional Hot-Racing Slipper Clutch Pads for the Traxxas Slash 4x4.     FEATURES Constructed of hard anodized CNC...

Hot Racing large heavy duty CNC machined hard anodized aluminum slipper pressure plate and hub for multiple Traxxas vehicles. This slipper system can accommodate three long Hot Racing slipper pads...

.

This is the the optional Hot-Racing 90T 48P Aluminum Spur Gear for the Traxxas Electric Stampede and Rustler series.     FEATURES CNC...

This is the Hot Racing Ball Bearing Equipped Steering Bellcrank for the Traxxas 2WD Slash, Rustler, and Bandit.     FEATURES 6061...

This is the the optional Hot-Racing Aluminum Transmission Case for the Traxxas Bandit, Rustler, 2WD Stampede, and 2WD Slash.     FEATURES ...

This is the Hot Racing Composite Gear Case with Aluminum Motor Plate for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.     FEATURES ...

These are the optional Hot-Racing 12mm Wheel Hexes for the 1/10 scale 2WD Traxxas Slash, Rustler and Stampede. **Will NOT fit the 4WD Traxxas Slash**     ...

.

This is the Hot-Racing Hard Aluminum Differential Case for the Traxxas Summit.     FEATURES CNC machined 6061-T6 aluminum construction...

This is the Hot-Racing 75T 48P Hardened Steel Spur Gear for the Traxxas 2WD Bandit, Slash, Electric Rustler and Electric Stampede.     FEATURES ...

This is the the optional Hot-Racing 73T 48P Steel Spur Gear for the Traxxas Bandit, 2WD Slash, Rustler, 2WD Stampede and Telluride.     FEATURES ...

This is the the optional Hot-Racing 72T 48P Steel Spur Gear for the Traxxas Bandit, 2WD Slash, Rustler, 2WD Stampede and Telluride.     FEATURES ...

Hot Racing optional upgrade heavy duty splined star drive axle kit for the Traxxas 2WD electric Stampede and electric Rustler FEATURES: - Heavy duty CNC machined #45 hardened carbon steel...

This is the Hot Racing 18T/60T Pinion and Spur Gear Set for the 2WD Traxxas Bandit, Rustler, Slash and Stampede.     FEATURES CNC...

This is the Hot-Racing Transmission Gear Locker for the Axial Wraith, AX10, SCX10 and Scorpion.     FEATURES CNC machined hardened...

This is the Hot Racing Hardened Steel Light Idler Gear for the Axial Wraith, AX10, and SCX10 transmissions.     FEATURES CNC machined...

This is the Hot-Racing Hardened Steel Light Weight Gear Set for the Axial AX10, Wraith and SCX10.     FEATURES Constructed of CNC...

Front and rear sway bar set for the Traxxas Slash 4x4, Slash 4x4 LCG, and 1/10 Rally vehicles. FEATURES:- Adjustable spring steel sway bar wire- A set of three sway bars for a wider range of...

These are the optional Hot-Racing Speed Tuned Pinion Gears for the Traxxas Slash 4x4.     FEATURES CNC machined 6061 aluminum Hard...

These are the Hot Racing 12mm Wheel Hex Extensions.     FEATURES Aluminum construction, silver in color Fits the 5mm diameter axles on...

.

This is the the optional Hot-Racing 65T Steel Spur Gear for the Traxxas E-Maxx, E-Revo, 1/8 Funny Car, and Summit.     FEATURES CNC...

This is the the optional Hot-Racing 88T 48P Aluminum Spur Gear for the Axial Wraith, SCX10, and AX10.     FEATURES CNC machined billet...

This is the optional Hot-Racing Center Gear Case for the Axial AX-10.     FEATURES CNC 6061 T-6 aluminum construction, black in...

This is the optional Hot-Racing 107-142mm Steel Center Drive Shaft     FEATURES Fits the Tamiya CC-01, CR-01 (front) Axial AX10...

These are the Hot-Racing Red Aluminum Suspension Pivot Balls.     FEATURES Machined aluminum construction, red in color   ...

This is the Hot Racing Splined Star Drive CVD Axle Kit.     FEATURES Fits the Traxxas 1/10 scale E-Revo, E-Maxx, Revo 3.3, T-Maxx 3.3...

These are the optional Hot-Racing Ball Type Aluminum Shock Ends. for the Traxxas Revo 3.3     FEATURES Aluminum construction, silver...

Hot Racing universal clip on motor heat sink and fan for use on 540 and 550 size motors. Versatile two-piece heat sink clip provides 8 different width adjustments.  FEATURES: - Keeps the...

This is the Hot-Racing Aluminum Inner Roll Cage for the Traxxas for use on the 1/10 Rally, or LCG Slash 4x4.     FEATURES Aluminum...

This is the Hot Racing Aluminum Rear Bumper for the Traxxas E Revo 2FEATURES:CNC Constructed of aluminum anodized Black in colordesign with LED light holder on each sideYOU WILL RECEIVE:One Aluminum...

Hot Racing CNC machined billet aluminum Center Skid Plate for the Traxxas E-Revo 2.0FEATURES:- CNC machined billet aluminum Center Skid Plate Anodized Black- Replaces factory plastic skid plateYOU...

This is a pair of optional Hot-Racing 89mm Rear Turnbuckles for 1/10 scale 2WD electric ECX Vehicles.     FEATURES Fits the ECX Boost...

Hot Racing optional aluminum rear lower suspension arms for the 1/10th ECX 2WD vehicles, including the Circuit Stadium Truck, Ruckus Monster Truck, and Torment SCT.  FEATURES: - CNC...

Hot Racing optional aluminum front lower suspension arms for the 1/10th ECX 2WD vehicles, including the Circuit Stadium Truck, Ruckus Monster Truck, and Torment SCT.  FEATURES:  - CNC...

This is a pair of optional Hot-Racing CV Drive Shafts with Hubs for 1/10 scale 2WD Electric ECX Trucks.     FEATURES Fits the ECX...

This is a Power Up Gear Adapter for the B4 B5 and most Team Associated vehicles by Hot Racing FEATURES Eliminating the Slipper assembly still use the stock or any spur gear for the B4, B5 Great...

This is a pair of optional Hot-Racing Aluminum C-Hubs for the Axial XR10, Wraith and Ridgecrest.     FEATURES 6061-T6 CNC machined...

This is a pair of Hot-Racing 1/10 scale Tow Shackle D-Rings.     FEATURES Fits the Axial SCX10 Jeep, AX80125 front bumper, AX80126 rear...

This is the Hot-Racing Aluminum Silver Tow Shackles D-Rings for the Axial SCX10 Jeep.     FEATURES Die-cast metal construction with...

Hot Racing heavy brass outer portal drive housings for the front of the Red Cat Gen 8 crawler. Adds weight to Red Cat Gen 8 crawler where it needs it - down low. Adds around 63g per hub to lower the...

Hot Racing optional upgrade heavy duty Center Drive Cv Splined Shaft E-Revo, E-Revo 2 Summit FEATURES: - CNC machined #45 hardened carbon steel and Aluminum construction - Replaces factory plastic...

Replace the stock plastic body posts on your Traxxas E-Revo 2.0 with this good looking aluminum front body mount from Hot Racing FEATURES: - Aluminum construction, black in color YOU WILL...

Hot Racing optional upgrade aluminum front chassis brace for the Losi 1/5th scale Desert Buggy XL (DB XL) FEATURES: - CNC machined 6061-T6 aluminum construction - Black anodizing for...

Silicone Rubber BODY CLIP RETAINERS 1/8 SCALE (4) BlueFEATURES:Silicone flexible rubber for durabilityRubber grommet for EZ attaches retainer to the bodyshellLarge pull tab allows easy body clip...

Hot Racing aluminum octopussy slipper pad for 1/10 Arrma 4X4 vehicles. See requirements and comments below for specific vehicle fit information.FEATURES:- Cross-drilled aluminum construction for...

Hot Racing's adjustable aluminum steering bellcrank and servo saver for the 1/10th scale 2WD electric Arrma vehicles, including the Raider, ADX-10, Vortex, Granite, Fury and Mojave FEATURES:...

Hot Racing optional aluminum rear hubs (knuckles) for for the 1/10th scale 2WD electric Arrma vehicles, including the Fits the Arrma Raider, ADX-10, Vortex, Granite, Fury, and Mojave FEATURES:...

Hot Racing optional Modifier aluminum steering (steer) blocks (knuckles) for the 1/10th scale 2WD electric Arrma vehicles, including the Fits the Arrma Raider, ADX-10, Vortex, Granite, Fury and...

Hot Racing heavy duty aluminum Front Chassis brace Infrection and Limitless Roller . See vehicle model compatibility in comments below.FEATURES:- CNC machined 6061 aluminum, anodized black- Machined...

Hot Racing heavy duty aluminum wing mount for the 1/8 Arrma Kraton BLX, Talion BLX, and Typhon BLX. See vehicle model compatibility in comments below.  FEATURES: - CNC machined 60601...

Hot Racing aluminum sliding channel lock motor mount for the Arrma Kraton BLX, Outcast BLX, Senton BLX, Talion BLX, and Typhon BLX. See vehicle model compatibility in comments below...

Hot Racing Aluminum Center Differential Rear Output mount for the for the Arrma Kraton BLX, Outcast BLX, Senton BLX, Talion BLX, and Typhon BLX. See vehicle model compatibility in comments below...

Hot Racing aluminum HD front shock Tower for the Arrma Kraton BLX, Outcast BLX, Talion BLX, FEATURES: - CNC machined 6061 aluminum- More suspension tuning position - Black anodized -...

Hot Racing Speed Run Center differential spool (locker) hub for the 1/8 Arrma Kraton BLX, Notorious BLX, Outcast BLX, Senton BLX, Talion BLX, and Typhon BLX. This part replaces the center...

Hot Racing aluminum differential carrier (case) for the 1/8 Arrma Kraton BLX, Notorious BLX, Outcast BLX, Senton BLX, Talion BLX, Typhon BLX and 1/7 LimitLess InFraction, Fits the front, center, or...

Hot Racing aluminum REAR hinge pin brace arm mount on the REAR LOWER suspension of Arrma 1/7 On Road, 1/8 4X4 vehiclesFEATURES:- Eliminates the need for stock plastic and stamp aluminum hinge pin...

This is a pair of aluminum Upper brace Rod ends for the Arrma Kraton BLX, Notorious BLX, Outcast BLX, Talion BLX, Infraction, Limitless Roller and - Mojave. See vehicle model compatibility in...

Hot Racing heavy duty aluminum rear brace BXL 6S the Arrma 1/7 1/8 Kraton BLX, Notorious BLX, Outcast BLX, Talion BLX, Infrection, Limitless Roller and Mojave . See vehicle model compatibility in...

This is the Hot Racing Foldable Winch Anchor.  FEATURES: -For use in conjunction with a scale winch to provide a winch point -Metal Die Cast and CNC construction -Blue and Black in...

Hot Racing metal dangler balls (truck nuts) RC scale accessory FEATURES: - Real metal 3D casting with black chrome finish YOU WILL RECEIVE: - One (1) dangler balls - One (1) flat head cap...

This is the Hot Racing Scale Accessory Sleeping Bag FEATURES: For 1/10 scale rock crawlers and monster trucks Polyester army digital camo shell with black Liner Detail with side zipper and...

Hot Racing EZ Pulls for 1/10 scale Cars body clips FEATURES: CNC Machine from durable Aluminum for lasting performance EZ pulls attach to the body clips so then the body clips are easier...

Hot Racing EZ Pulls for 1/10 scale Cars body clips FEATURES: CNC Machine from durable Aluminum for lasting performance EZ pulls attach to the body clips so then the body clips are easier...

Hot Racing +4mm wide track hardened steel axles set for the Axial SCX 24 These add 5mm to the track width on each side of the vehicle to add stability over rough terrain, increase steering clearance,...

Hot Racing steel universal center joint axles for the Axial SCX 24 Dead Bolt chassisFEATURES:- CNC Hardened steel construction, black finishedYOU WILL RECEIVE:- One (1) Long steel u-joint center...

Hot Racing aluminum swaybar ready lower arm set for the Losi Rock ReyFEATURES:- CNC machined 6061-T6 aluminum, anodized black- With Sway Bar Bar Mount for LRR311FYOU WILL RECEIVE:- Two (2) lower...

Hot Racing optional aluminum front camber link mount for the Losi Rock ReyFEATURES:- CNC machined 6061-T6 aluminum, anodized black- Stronger and more rigid than stock plastic component- Retains...

Hot Racing front or rear Brass hub adapters for Element Enduro vehiclesFEATURES:- CNC machined solid brass billet- Emliminate the the stock hex drive- Adds g per hub to the Stock Wheel location of...

Hot Racing +10mm wide track S2 hardened spring steel portal drive stub axles for the Axial UTB SCX 3 .These add 10mm to the track width on each side of the vehicle to add stability over rough...

Hot Racing single arm aluminum Clamp servo arm for Axial UTBFEATURES:CNC Aluminum construction,Anodized Black in colorone diameter linkage holesYOU WILL RECEIVE:one black single arm...

Hot Racings CNC machined aluminum Rear axle housing for the Axial UTB vehiclesFEATURES:- CNC machined billet aluminum axle housing and tubes, anodized Silver- Replaces factory plastic axle case...

Hot Racings CNC machined aluminum Rear axle housing for the Axial UTB vehiclesFEATURES:- CNC machined billet aluminum axle housing and tubes, anodized Black- Replaces factory plastic axle case...

Hot Racing optional upgrade heavy duty splined star drive axle kit for 1/10 Arrma 4X4 vehicles. See comments below for specific vehicle fit information.FEATURES:- Replaces stock diff outdrives and...

Hot Racing aluminum threaded front shock bodies for 1/10 Arrma 4X4 Mega and 3S BLX vehicles. See vehicle compatibility in comments below.FEATURES:- Threaded shock bodies for easy, precise, and...

Hot Racing heavy duty Aluminum Lower Diffuses Wing mount 1/7 On Road Arrma LimitlessFEATURES:- CNC machined 6061 Aluminum Lower Diffuses Wing mount 1/7 On Road Arrma Limitless- Anodized black with...

Hot Racing #45 Steel 34T Mod1 Spool Gear allows you to fine tune the gearing of your Limitless vehicleFEATURES:Strong and durable steel for long-lasting performance in extreme RC conditions -...

Hot Racing heavy duty aluminum Rear Chassis brace Infrection and Limitless Roller . See vehicle model compatibility in comments below.FEATURES:- CNC machined 6061 aluminum, anodized black- Machined...

Hot Racing #45 Steel 29T Mod1 Spool Gear allows you to fine tune the gearing of your vehicleFEATURES:Strong and durable steel for long-lasting performance in extreme RC conditions - Precision...

Hot Racing Speed Run Center differential spool (locker) hub for the 1/7 Limitless RollerFEATURES:- Heavy duty CNC machined S2 spring steel Spool shaft- CNC Aluminum Pin capture rings- Allows for...

Hot Racing Aluminum Shock Collar Clamp Arrma shock for 1/5th scale Arrma vehiclesFEATURES:- CNC machined 6061-T6 aluminum, anodized black- Screw Clamp provides sure gripYOU WILL RECEIVE:- Two (2)...

Hot Racing optional aluminum shock cap for the Arrma 1/5 Shock bleeder caps- CNC machined aluminum construction, anodized black- Secondarily processed machined beveled edges- Bleeder screws for easy...

Hot Racing aluminum 1/10th scale black tow shackles (D-rings) for the Red Cat Gen 8 front and Rear bumper, the or other custom projectFEATURES:- Metal case with a high level of detail for a realistic...