NCE CORPORATION

The Cab06 uses a more conventional knob for speed control and is available with either a potentiometer (Cab06p) or digital encoder (Cab06). Both varieties of the Cab06 can be set to YARD mode. Yard...

FeaturesUse with any DCC system to prevent large voltage spikes.Reduces or eliminates voltage spikes on long runs of DCC bus wireProtects decoders from damaging inductive voltage spikesSolve...

12/13.8 Volt DC, 5 Amp internationally approved power supply.for use with SB5, DB5, and PB5 

The front two sockets connect to our RJ12  modular Cab cables while the rear two sockets connect to CAT5 cables.Faceplate Dimensions: 3" x 2" 

.

RJ/12-7,   6 Wire straight cab bus cable, 7 foot long

Product Description   Overview   Detects DCC current being drawn in a block.  Connects to AIU01 or Mini Panel Isolated so that there is no electrical connection to the track...

The Auxiliary Input Unit provides connection of block occupancy detectors, switch position relays, etc. for purposes of signaling and/or computer control of your layout.Simply plugs in to the Cab Bus.

D13J Decoder - New Smaller Replacement For D13SRJDirect Plug In to Athearn and Other LocosEquipped With NMRA 9 Pin DCC “Quick Plug”Silent Running, Torque Compensated Motor DriveTorque Compensation...

4-Pack of NCE HO scale universal decoder with 3.5-inch hard-wire harness. 4 functions and 15 different lighting effects. Instructions included. This smaller-sized decoder replaces the D13SR...

NCE HO scale universal decoder with 3.5-inch hard-wire harness. 4 functions and 15 different lighting effects. Instructions included. This smaller-sized decoder replaces the D13SR. This decoder is...

.

The Illuminator is a Plug and Play multi-purpose programmable DCC lighting decoder. One Illuminator contains three programmable lighting outputs with a complete array of lighting effects. Suitable...

DescriptionWorks on DCC or DC (limited operation on DC)Works with loco, accessory, or signal addressingBuilt-In Warm white LED (can be disabled)Up to 3 LEDs may be controlled separately 5v with 3 -...

3-Pack of NCE Light-It programmable DCC lighting and signal decoders with built-in white LED. The Light-It is a multi-purpose programmable DCC lighting decoder. One Light-It contains three...

N12-NEM Plug In 4 Function Decoder With 6 Pin NEM 651 Connector

Plug and play decoder for N-Scale Atlas H15-44 and H16-44Features of this decoder: Preprogrammed marker lights change color depending on direction Silent Running, torque compensated motor...

8 function decoder with 21 pin 'MTC' plug.Dimensions: 0.900 x 0.615 x .180 inches – 23 x 16 x 4.7 mmDirect plug in to locos equipped with NMRA 21 pin MTC (NEM651) plugFeatures of this decoder::Silent...

The NCE Switch-It is a two-address decoder specifically designed to drive stall motor switch machines. It therefore does not have some of the features that the other decoders have.  It is the...

The Switch-8 MK2 is all new with easy programming no jumpers are required, and on board display.Switch-8 MK2 Features:Control for 8 Tortoise switch machinesRemembers the position of switch during...

N Scale Plug and Play decoder for the new Atlas "Classic" locomotives GP30, GP35, GP7, GP9

This decoder is specifically designed as a replacement for "Bachmann DCC Equipped" diesels. Providing a more smooth, more quiet operation.The decoder has 4 function outputs. Complete...

Available with a wire harness. Four function outputs. 1 Amp rating, 1.25 Amp peak. Measures 1.15" x 0.4" x 0.12".

Plug and Play decoder for the N scale Atlas SD50, SD60M, SD60.

Control one twin coil switch machine. Has capacitive discharge for low current draw of track power. Provides connections for two "local control" pushbuttons. You can control switches from your...

10 Amp Power Booster recommended for O, G and other large scales ONLY. The PB-110A provides true 10 Amps of continuous voltage to your track. Enough to handle MUs of the largest locomotives.The...

Intermediate standard cab with potentiometer speed control.LED DISPLAYThis 4 digit display normally indicates the current locomotive address and its forward/reverse status.SPEED KNOBThis knob...

This is a true 5 Amp booster compatible with all NCE and most other DCC systems.Includes an Internationally Approved Power Supply (US/CA/UK/AU)Works with Auto Reverse's and Circuit Breakers.Plastic...

Product Description Overview An entire DCC system in the palm of your hand! This 2 Amp system can operate 2 or 3 HO sized trains, or 4 N scale trains. Installation is a snap. Hook two wires to your...

The P1024 is a 24 Volt DC, 220-watt power supply with a US power cord.The power supply is suitable for use with the following NCE products: PB110 booster, PH10, PH10-R (10 amp systems).Note: The...

D13J-10 1.2 Amp 4 Function NMRA 9 pin Decoder - 10 PackNCE Item #5240176D13J Decoder - New Smaller Replacement For D13SRJDirect Plug In to Athearn and Other LocosEquipped With NMRA 9 Pin DCC “Quick...

Command Station Only. No track Power Booster.FYI: Not for use with the Power CabContents included with CS03:One 2-pin plug for the programming trackOne 7 foot 4 wire Control Bus cableOne P118 Power...

This power supply is suitable for use with the following NCE products: PH5 (5 Amp systems)Note: For the older PowerPro 5 Amp NCE Systems or the PB105 booster, the customer should cut off the round...

Engineer cab with LED display, uses a digital encoder which allows flexibility when controlling multiple locomotives at different speeds. Clear, easy-to-read display, select up to 6 loco recalls,...

.

D13W Decoder - New Smaller Replacement for D13SRDimensions: 1.03 x 0.630 x .185 inches – 26 x 16.5 x 4.7 mmSilent Running Torque Compensated Motor DriveTorque Compensation for Ultra Smooth Low Speed...

NCE DCC  #165 Illuminator - 5 Pack DCC Decoder compatible with Woodland Scenics Just Plug System products and other lighting accessories with built in resistors. Features of...

 Add Push Buttons or Toggle switches to a Switch8 Mark2For Use w/Switch8-MK2 Switch Machine Decoder #524-151

.

.

TS6S On/On SPST Toggle Switch 6-Pack -125V - 5A

NCE Euro12-2 - 12 Circuit Eurostyle Term Strip - Package of 2. (14-24 AWG)

AND-24 Anderson Power Poles 24 Pack 12 each Red / Black

AND-8 Anderson Power Poles 8 Pack 4 each Red / Black

.

NCE TBTB20 Blue Track Bus Taps, 14-16 Gauge, 20pk 

.

NCE TBTB32 Blue Track Bus Taps, 14-16 Gauge, 32pk 

.

.

Complete set to expand or upgrade a layout, optimal wiring for five amp and lower power systems, and connections can be easily disconnected for trouble-shooting.  Includes Main Bus (50'...

.

Ultraflex Wire 32 Gauge 10ft White

Ultraflex Wire 32 Gauge 10ft Gray

Ultraflex Wire 32 Gauge 10ft Blue

Ultraflex Wire 32 Gauge 10ft Green

Ultraflex Wire 32 Gauge 10ft Yellow

Ultraflex Wire 30 Gauge 10ft Red

.

The UTP-CAT5 Adapter lets you change from our RJ12 plug to the CAT5 plug so that you can use the existing Cab Bus cable you already have!

DescriptionWorks on DCC or DC (limited operation on DC)Works with loco, accessory, or signal addressingBuilt-In Warm white LED (can be disabled)Up to 3 LEDs may be controlled separately 5v with 3 -...

NCE NHI-MED Medium Size "No Halt" Add On ModuleHigh Power Version for Larger LocomotivesEliminates or Reduces the Following Due to Dirty Track or Unwired Switchfrogs:• Stalling• Sound interruption•...

Available with a wire harness. Four function outputs. 1 Amp rating, 1.25 Amp peak. Measures 1.15" x 0.4" x 0.12".

Available with an eight pin plug in. Four function outputs. 1 Amp rating, 1.25 Amp peak. Measures 1.15" x 0.4" x 0.12".

D13J Decoder - new smaller replacement for D13SRJ Dimensions: 1.03 x 0.630 x .185 inches – 26 x 16.5 x 4.7 mm Direct plug in to Athearn and other locos equipped with NMRA 9 pin DCC...

This is a true 4 Amp (12 Amp peak) self contained decoder for S, O and large scale with connectorized wire harnesses. Functions supported: Headlight(s) plus seven additional function outputs. All...

Add this USB computer interface for computer programming and/or operation of your Power Cab equipped layout. Requires USB cable, computer and railroad computer program such as JMRI Decoder Pro and...