Digitrax

Features:Wired Mobile Decoder with SoundFX® & FX3 Function for most HO and many N scale Locomotives.Preloaded with selectable generic steam and diesel sound schemesVisit Digitrax Sound Depot to...

Fits Kato N Scale 4-8-4 FEF and similar LocomotivesDrop In Mobile Sound Decoders for Kato N scale Locomotives1.0 Amp/2 Amp Peak4 FX3 Functions, 200ma output8 Ohm 10 mm x 18 mm Oval Speaker100uF...

Fits Kato N Scale SD80 MAC and similar LocomotivesDrop In Mobile Sound Decoders for Kato N scale Locomotives1.0 Amp/2 Amp Peak4 FX3 Functions, 200ma output8 Ohm 10 mm x 18 mm Oval Speaker100uF...

Fits Kato N Scale SD40-2 and similar LocomotivesDrop In Mobile Sound Decoders for Kato N scale Locomotives1.0 Amp/2 Amp Peak4 FX3 Functions, 200ma output8 Ohm 10 mm x 18 mm Oval Speaker100uF...

Materials for making 2 Signal Driver Cables for SE8C. Includes 30’of 10-wire Signal Driver ribbon cable & 8 10-Pin sockets.Use this kit to make signal driver cables to connect your SE8c to the...

The RX4 is a 4 zone transponder detector for use with Digitrax occupancy detection systems.  The RX4 enables you to not only see what blocks are occupied but also identifies what is there.RX4...

RD2 Remote Sensing Diodes for BDL16 series occupancy detectorsRemote sensing of 2 detection sections. Eliminates the need for long runs of heavy gauge wire between the BDL168, BDL16 & BDL162 and...

Keeps locos & sound running during power interruptions caused by dirty or bad track.Hold up time varies based on decoder load & track conditions.PX112-2 Plug ‘N Play Install on DH126 &...

For use with Digitrax Decoders Equipped with 2 pin PX socket or solder pad connectionsKeeps locos running during intermittent power interruptions resulting from dirty or bad track.0.33 F...

PS615 90W AC/DC 15VDC 6 amp power supply for use with all Digitrax Command Stations and Boosters operating at 5 amps.High-efficiency power supply15 VDC outputAccepts different cord setsMeets MEPS VI...

The LT1 is included with all Digitrax Starter Sets. It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2...

Use with crimper tool to make custom length LocoNet cables & replace broken plugs.SpecificationsFor Use WithDigitrax Layouts and Throttles

Use for joining LocoNet Cables, adding coiled cords to throttles, etc.SpecificationsFor Use WithDigitrax Layouts and Throttles

LocoNet Layout Wiring Made Simple!Pre-made, pre-tested 50 foot LocoNet cable.Use on any LocoNet Layout.Use for long runs or divide into custom lengths using LocoNet Cable Maker Kit & RJ12 Plugs...

2 pack of 16' LocoNet Cables.Convenient pre-made, pre-tested cables, ready to use on your layout.LocoNet Wiring is a snap with these cables. SpecificationsFor Use WithAll LocoNet Layouts

Basic Quad Stationary Decoder for Slow Motion Turnout Machines, add cost effective DCC control to your slow motion turnouts. DS44 Features:No frills stationary decoder.Simple installation and...

Lets you share decoders among locomotives4” wires make it easy to install in N or HO5-Pack

Lets you run locos as DC or DCCFor DC only operation use the dummy plug with either DNWH or DNWHPSFor DCC operation remove the DNDP and replace with a decoder5-Pack

For Intermountain N scale FT B units with motor contact "shoes"6 FX3 Functions.472” x 2.165” x .098”11.98mm x 54.99mm x 2.4 mmReplaces DN163I1B▪FX3 Function outputs for prototypical lighting effects...

For Intermountain N scale FT A units with motor contact "shoes"6 FX3 Functions.472” x 2.165” x .098”11.98mm x 54.99mm x 2.4 mmReplaces DN163I1A▪FX3 Function outputs for prototypical lighting effects...