Traxxas

Replacement hardened steel rear center driveshaft for 9655X hardened steel center CV driveshafts. (Does not fit standard center driveshafts)Accessory part for these models:Sledge®

This is the Boat Stand for the Traxxas DCB-M41 40" Twin Hull Catamaran. FEATURES Plastic construction with matte black finish Easy slotted assembly, no glue or hardware required Foam...

.

FEATURES: Alias ribbed tires For use on front of buggy Soft compound INCLUDES: Two Traxxas Alias Ribbed 2.2" tires REQUIRES: Wheels Tire Glue SPECS: Inner Diameter: 2.2" (55.8mm) Outer Diameter: 3.14" (80mm) Width: 1.37" (35mm)

ANACONDA 2.2" TIRES: Anaconda 2.2" performance street tires provide exceptional wear and sticky traction for high-speed asphalt action. Fits Traxxas and other standard 2.2" buggy wheels. FEATURES: Rubber Anaconda tires Split X-Pattern tread Foam...

FEATURES: Plastic construction, white in color INCLUDES: Two Dish Rear Wheels in White REQUIRES: Tires Tire Glue  SPECS: Diameter: 3.4" (87mm) Width: 2" (51mm) Hex Size: 17mm

This is the Rebuild Kit for the Traxxas Velineon 3500kV Brushless Motor.       FEATURES Restores like new performance to the #3351R Velineon brushless motor     ...

.

These are the (optional) Red Aluminum Pushrods for the Rocker Arms These go between the Rocker Arms and the Lower Suspension Arms **Must be used with Progressive-1 Rocker Arm Set, .** FEATURES: Red Aluminum construction INCLUDES: Two Pushrods...

These are the (optional) Red Aluminum Pushrods for the Rocker Arms These go between the Rocker Arms and the Lower Suspension Arms **Must be used with Progressive-3 Rocker Arm Set.** FEATURES: Red Aluminum construction INCLUDES: Two Pushrods...

FEATURES: Aluminum construction Gun Metal in color Threaded on one end w/machined nut at center of post INCLUDES: Four Rocker Arm Posts REQUIRES: Assembly to vehicle SPECS: Overall length: 33.5mm (1.32") Internal thread size: M4x.70mm coarse External...

Traxxas 8369 Tires Response 1.9 Touring (Front) (2)/ Foam Inserts (2) Brand new item, sealed in original retail packaging. Tires, Response 1.9' Touring (front) (2)/ foam inserts (2)

Part Number: TRA8370 Description: Traxxas Tires Response 1.9' Touring (Extra Wide, Rear) - TRA8370 This item package consists of the following Traxxas items. Tires, Response 1.9' Touring (extra wide, rear)/ foam inserts (2) (fits #8372...

FEATURES: Machined aluminum 30T idler gear Hard anodized INCLUDES: One Auminum Idler Gear REQUIRES: Two 5 x 11mm bearings (DTXC1547) One #3195X top drive gear (TRAC3296) COMMENTS: This idler gear is not for use with the original steel top gear #3195 (per...

FEATURES: Aluminum Construction Anodized blue INCLUDES: (2) Assembled Turnbuckles REQUIRES: Installation onto Stampede 5mm Wrench SPECS: Length: 2.4" (61mm)

FEATURES: Aluminum Construction Anodized Red INCLUDES: (2) Assembled Turnbuckles REQUIRES: Installation onto Stampede 5mm Wrench SPECS: Length: 2.4" (61mm)

.

Adapter, Traxxas iD LiPo battery (adapts Traxxas iD batteries to separate balance ports) Traxxas Balance Lead Adapter enables customers to connect their Traxxas iD batteries to accessory cell voltage checkers without using the EZ-Peak Live app with...

FEATURES: Aluminum construction Anodized Blue INCLUDES: Two assembled turnbuckles REQUIRES: Installation, 5mm Wrench

Turnbuckles, aluminum (green-anodized), toe links, 59mm (2) (assembled w/ rod ends & hollow balls) (requires 5mm aluminum wrench #5477)Accessory part for these models:Ford® F-150 RaptorFord® Fiesta® ST RallyNitro SlashRustler® VXLRustler®Slash 2WD...

Turnbuckles, aluminum (pink-anodized), toe links, 59mm (2) (assembled w/ rod ends & hollow balls) (requires 5mm aluminum wrench #5477)Traxxas’ aluminum toe links make it easy to add strength and adjustability to your Traxxas model. These toe links...

Turnbuckles, aluminum (orange-anodized), toe links, 59mm (2) (assembled w/ rod ends & hollow balls) (requires 5mm aluminum wrench #5477)Traxxas’ aluminum toe links make it easy to add strength and adjustability to your Traxxas model. These toe links...

FEATURES: Aluminum construction Anodized Red INCLUDES: Two assembled turnbuckles REQUIRES: Installation, 5mm Wrench

FEATURES: Nylon construction Black in color INCLUDES: One Receiver Box One Rubber Seal Foam Padding Two 2.5x8mm Cap Head Screws Two 3x10mm Cap Head Screws Two 2.5x10mm Cap Head Screws One Tube of Grease Instruction sheet REQUIRES: Installation on the...

FEATURES: Replaces damaged receiver boxes Constructed of black plastic INCLUDES: One top and bottom half receiver box for the Traxxas E-Maxx Hardware REQUIRES: Installing receiver and bolting receiver box to chassis.

 This is the Lightweight Output/Idler Gear Shaft for the Traxxas E-Maxx. This shaft is located in the gearbox between the Drive Dog, key #3986 (TRAC3986) and the #3984 Output Gear (TRAC3984). FEATURES Lighter weight upgrade from stock output...

FEATURES: Fits all Traxxas 1/10th scale nitro vehicles. Replaces worn or damaged clutch bells. Constructed of hardened steel. INCLUDES: One Traxxas 18 Tooth Steel Replacement Clutch Bell. Two 5mm x 10mm 0.5mm fiber washers. Two 5mm E-clips. REQUIRES:...

FEATURES: Fits all Traxxas 1/10th scale nitro vehicles. Replaces worn or damaged clutch bells. Constructed of hardened steel. INCLUDES: One Traxxas 20 Tooth Steel Replacement Clutch Bell. Two 5mm x 11mm 0.5mm fiber washers. Two 5mm E-clips. REQUIRES:...

Features: Clear plastic, flip-top style tank for glow fuel only. Nipples for fuel outlet and muffler pressurisation are conveniently located on the top of the tank Muffler pressurisation nipple is fitted with a check ball to prevent back-flow and keep...

FEATURES: Aluminum construction Hex drives and phillips drive INCLUDES: One engine mount Two upper plates Hardware SPECS: Length of engine mount 64mm (2.51") and Width: 65mm (2.56") Length of left mounting plate 52mm (2.06") and Width: 23mm (.90") Length...

.

FEATURES: Stainless steel construction. INCLUDES: Four 3x70.5mm pins for the upper front and rear suspension arms. Two 3x63mm pins for the lower front suspension arms. Two 3x57mm pins for lower rear suspension arms. Eighteen e-clips REQUIRES: Inserting...

FEATURES: Metal construction Black in color INCLUDES: One differential spool REQUIRES: Assembly onto a T-Maxx truck.

FEATURES: Metal construction Five cooling holes on the face of bell (bellow the teeth) INCLUDES: One clutch bell Part #5214 Two washers Part #1985 Two e-clip Part #1633 REQUIRES: This clutch bell uses different bearings than the 15T or 16T bell, you will...

FEATURES: Vented clutch bell One piece bell design INCLUDES: One 15 tooth black vented clutch bell Two 5x8x0.5mm fiber washers One 5mm e-clip REQUIRES: Using the original 5x11x4mm clutch bell ball bearings

FEATURES: Metal construction Five cooling holes on the face of bell (bellow the teeth)INCLUDES: One clutch bellTwo washersTwo e-clipREQUIRES: This clutch bell uses 5X11 bearings #4611 (not included)SPECS: Diameter at the base: 15/16" (24mm) Height:...

FEATURES: Fits Traxxas 1/10 scale nitro vehicles Replaces worn or damaged clutch bells Constructed of hardened steel INCLUDES: One Traxxas 17 Tooth Steel Clutch Bell Two 5mm x 8mm 0.5mm fiber washers Two 5mm E-clips REQUIRES: Disassembly of flywheel,...

FEATURES: Black plastic air filter housing with cover screen and and changeable element Rubber angled neck for filter Rubber adapter for filter Zip tie for fastening INCLUDES: One screened filter One rubber straight neck One rubber adapter One zip...

FEATURES: Black plastic air filter housing with cover screen and and changeable element Rubber double angled neck for filter Zip tie for fastening INCLUDES: One screened filter One rubber double angled One rubber adapter One zip tie REQUIRES: TRX 2.5...

FEATURES: Plastic construction Black in color INCLUDES: One Air Filter Housing One Foam Insert Element One Rubber Filter Base One Cable Tie SPECS: Diameter at Mounting Base: 0.55" (14mm) Diameter of Outer Housing: 1.6" (40mm) Height Including Mounting...

FEATURES: Replaces worn or damaged air filter components INCLUDES: Foam Filter Element with Plastic Holder with Body Clip, Rubber Connector and Wire Bracket

This is the optional Differential Spool for the Traxxas Revo. FEATURES Constructed of steel Installs in diff housing on either front or rear wheels ...

FEATURES: Fully assembled Plastic telescoping drive shaft with steel universals Blue rubber boot shields telescoping sections from dirt Attaches to the differential with one screw pin Works on the front or rear, right or left of vehicleINCLUDES: #5458X...

FEATURES: Nylon and metal construction Black and silver in color INCLUDES: Two 3x70mm assembled front turnbuckles with rod ends, hollow balls and ball studs REQUIRES: The remaining parts of the sway bar kit - TRAC5598

FEATURES: Metal construction Silver in Color INCLUDES: One Silver Engine Mount Two Engine Mount Spacers Four 3mm x 15mm Socket Head Screws w/Washers Two 4mm x 18mm Button Head Screws Two 3mm x 10mm Flat Head Screws REQUIRES: Assembly onto Vehicle

FEATURES: Steel construction Black in color INCLUDES: Two Differential Output Gears Two Spider Gears Two Spider Gear Shafts REQUIRES: Assembly onto Vehicle

FEATURES: Steel construction INCLUDES: One Locking Differential Output Gear One Differential Slider One 3x12mm Screwpin REQUIRES: Installation on the vehicle  

.

Bumper, front/ bumper mount, front/ adapter (fits 2017 Ford Raptor)

FEATURES: Constructed of molded plastic, black in color INCLUDES: Rear Wing with two Mounts and two Washers

FEATURES: Plastic construction with one-piece silicone seal INCLUDES: All Receiver Box Compoments with Foam Mounting Pads, tube of Silicone Grease and Instructions

FEATURES: Molded plastic construction INCLUDES: Rear Diffuser

This is an optional Traxxas "Long" RPM Sensor, and is intended for use with the Traxxas XO-1 1/7 Scale vehicle. To collect critical RPM data (Revolutions Per Minute), a "trigger magnet" is installed in the spur gear of electric models, or the flywheel of...

This is an optional Traxxas "Long" Temperature & Voltage Sensor. Temperature data is critical to monitoring performance, gauging the effects of changes, and preventing overheating. The Temperature Sensor features a precision thermistor and is...

This is an optional Traxxas "short" RPM Sensor. To collect critical RPM data (Revolutions Per Minute), a "trigger magnet" is installed in the spur gear of electric models, or the flywheel of nitro vehicles. To offset the weight of the magnet, additional...

This is an optional Traxxas "Short" Temperature & Voltage Sensor. Temperature data is critical to monitoring performance, gauging the effects of changes, and preventing overheating. The Temperature Sensor features a precision thermistor and is...

This is a replacement Traxxas Temperature & Voltage Telemetry Sensor, and is intended for use with the Traxxas XO-1. Temperature data is critical to monitoring performance, gauging the effects of changes, and preventing overheating. The Temperature...

.

FEATURES: Composite nylon construction Replaces a worn or damaged bellcrank set May also be installed on the Traxxas Rustler, Bandit and 2WD Slash models (assembled in different configurations depending on model) INCLUDES: One Left Bellcrank Lower One...

FEATURES: Nylon construction          Black in colorINCLUDES: Upper and Lower Steering Arm          Steering...

FEATURES: Steel constructionINCLUDES: One Diff Ring Gear          One Pinion Gear

FEATURES: Plastic constructionINCLUDES: One Inner Shaft assembly          One M2x8 Screw Pin

FEATURES: Metal constructionINCLUDES: Driveshaft assembly

FEATURES: Plastic construction, black in color INCLUDES: Upper and lower Case Halves with Wire Cover Gasket Two Foam Pads Two 3x12mm Button Head Cap Screws Two 3x6mm Button Head Cap Screws Two 2.5x12mm Cap Screws Instruction Sheet SPECS: Box Dimensions:...

FEATURES: Polished spokes with blue finish Premounted slick rubber tires INCLUDES: Two Tires and wheels SPECS: Width: 0.70" (17.8mm) Diameter: 1.7" (43mm) Hex Size 7mm

FEATURES: Polished spokes with black chrome finish Premounted slick rubber tires INCLUDES: Two Tires and wheels SPECS: Width: 0.70" (17.8mm) Diameter: 1.7" (43mm) Hex Size 7mm

FEATURES: Polished spokes with blue chrome finish Premounted slick rubber tires INCLUDES: Two Tires and wheels SPECS: Width: 0.70" (17.8mm) Diameter: 1.7" (43mm) Hex Size 7mm

FEATURES: Polished spokes with red chrome finish Premounted slick rubber tires INCLUDES: Two Tires and wheels SPECS: Width: 0.70" (17.8mm) Diameter: 1.7" (43mm) Hex Size 7mm

FEATURES Molded composite plastic construction Steel servo saver spring   INCLUDES Two Steering Bellcranks Bellcrank Support Servo...

Drive cup (1)/ 3x8mm CS (use only with #7750X driveshaft) X-Maxx drive cup with 3x8mm CS hardware. For use with 8s-spec heavy duty driveshaft (#7750X) only.

This is the Center Driveshaft Assembly for the Traxxas X-Maxx Monster Truck     FEATURES Aluminum construction with natural silver colored finish Double sided steel gear meshes with...

FEATURES Aluminum construction, anodized blue in color Threads onto stub axles to hold wheels in place   INCLUDES Four 17mm Splined Wheel Nuts

Wheel nuts, splined, 17mm, serrated (black-anodized) (4)Accessory part for these models:X-Maxx

FEATURES Aluminum construction, anodized green in color Threads onto stub axles to hold wheels in place   INCLUDES Four 17mm Splined Wheel Nuts

FEATURES Aluminum construction, anodized red in color Threads onto stub axles to hold wheels in place   INCLUDES Four 17mm Splined Wheel Nuts

Receiver box cover (for use only with #8224 receiver box & #2260 BEC)/ foam pads/ seals/ silicone greaseAccessory part for these models:TRX-4® 1979 Chevrolet BlazerTRX-4® Equipped with Traxx™TRX-4® Ford BroncoTRX-4® Mercedes-Benz® G 500® 4X4²TRX-4®...

Body, GTS Shock, Aluminum Anodized (1) Accessory part for these models: TRX-4 Scale and Trail Crawler TRX-4 Tactical Unit

Body, GTS Shock, Aluminum Anodized (1) Accessory part for these models: TRX-4 Scale and Trail Crawler TRX-4 Tactical Unit

Body, GTS Shock, Aluminum Anodized (1) Accessory part for these models: TRX-4 Scale and Trail Crawler TRX-4 Tactical Unit

Transmission gears, single speed, metal

Description: Traxxas Chassis - TRA8322 This item package consists of the following Traxxas items. Chassis   For FORD GT

Description: Traxxas Stub Axles (2) - TRA8354 This item package consists of the following Traxxas items. Stub axles (front or rear) (2)   For FORD GT

.

.

.

.

.

Includes Main Housing, Front housing, & Cover

.

This is the USB Charger for the LaTrax Alias Quad-Copter Includes: 1 x High Output USB Charger

Box, receiver (sealed)/ wire cover/ foam pads/ silicone grease/ 3x8 BCS (5)/ 2.5x8 CS (2)

Requires #8216 ExoCage Fits #8011 Body

Rebuild kit, slipper clutch (steel disc (2)/ friction insert (2)/ 4.0mm NL (1)/ spring washers (2))

FEATURES: Certified for use with the Traxxas XO-1 on road car Withstands centrifugal forces at speeds in excess of 100mph Cyanoacrylate (CA) type glue Sealing pin designed into cap prevents clogging INCLUDES: 0.7oz (20g) bottle of Tire Glue and two...

FEATURES: Plastic construction, white in color INCLUDES: Two Dish Front Wheels in White REQUIRES: Tires Tire Glue SPECS: Diameter: 3.4" (87mm) Width: 1.7" (43.4mm) Hex Size: 17mm

FEATURES: Talon tread          Gray foam insertsINCLUDES: Two Talon Tires with Foam InsertsREQUIRES: Installation on the vehicle          Tire...

FEATURES: Nylon construction Black in color INCLUDES: Two black nylon suspension arms REQUIRES: Assembly onto kit. SPECS: Length: 3" Width: 1.2" COMMENTS: This will work on the Bandit, Nitro Stampede, Nitro Rustler, SRT, and the Nitro Sport.

FEATURES: Sturdy plastic construction, metal fuel nipple pre-installed and spring loaded cap for fast fill-ups. INCLUDES: 1 assembled fuel tank. SPECIFICATIONS: Length: 2-3/8" Width: 1-7/16" Height: 2-1/4" including the cap

.