Traxxas

Fits Continued: 1/10 Nitro Sport / Nitro Rustler FEATURES: Nylon construction Black in color INCLUDES: One front body mount One rear body mount Two 38mm body posts Two 26mm body posts Installation hardware

Includes: 2ea 24X3mm pins 4ea 31.5X3mm pins 2ea 40X3mm pins 2ea 48X3mm pins 10ea 3mm e-clips

Includes: 2 white nylon telescoping shaft (each shaft is made of two pieces) 4 aluminum U-joints

FEATURES: Three piece plastic case molded in blue and black color Replaces worn or damaged servo cases and gaskets INCLUDES: One Upper Case (blue plastic) One Middle Case (blue plastic) One Lower Case (black plastic) One Upper Case Gasket One Lower Case...

FEATURES: Nylon construction          Blue in colorINCLUDES: One Servo Case (Top, Middle, and Bottom Sections)          Five...

This is the Main Diff with Steel Ring Gear from Traxxas for the Bandit, Stampede and Rustler VXL series. Includes: Main diff with steel ring gear Side cover plate Screws Instructions Requires: Installation on the vehicle

Fits Continued: 1/10 Nitro Rustler FEATURES: All these gears and shafts are made of metal(probably with a low amount of steel). INCLUDES: 4- planetary gears 4- planteary gear shafts 2- sun gears 1- sun gear alignment shaft

.

.

The battery expansion kit from Traxxas allows the installation of larger format battery packs into the Velineon powered Rustler VXL and Stampede VXL. The package includes hardware to raise the electronic speed control mount and battery posts allowing...

FEATURES: Anodized aluminum construction, red in color Black nylon ball ends and steel link set INCLUDES: One 39mm red aluminum turnbuckle set with instructions REQUIRES: Installation onto vehicle

FEATURES: Anodized aluminum construction, blue in color Black nylon ball ends INCLUDES: One 39mm blue aluminum turnbuckle set with instructions REQUIRES: Installation onto vehicle

FEATURES: Anodized aluminum construction, red in color Black nylon ball ends INCLUDES: One 49mm red aluminum rear turnbuckle REQUIRES: Installation onto vehicle

FEATURES: Anodized aluminum construction, blue in color Black nylon ball ends INCLUDES: One 49mm blue aluminum turnbuckle REQUIRES: Installation onto vehicle

FEATURES: Plastic servo horn construction Steering rods come with rod ends installed INCLUDES: 2 steering servo horns 1 3x12mm threaded rod steering link with rod ends and hollow balls REQUIRES: Installation on the E-Maxx

FEATURES: White plastic construction INCLUDES: One 21T 1st speed gear One 18T input gear REQUIRES: Installation into Traxxas E-Maxx  

FEATURES: White plastic construction INCLUDES: One 26T 1st speed gear One 13T input gear REQUIRES: Installation into Traxxas E-Maxx

FEATURES: Steel construction, gun metal in color Replaces a worn or damaged idler gear INCLUDES: One 13 Tooth Idler Gear (first speed gear) REQUIRES: Installation

FEATURES: Blue anodized aluminum construction. Nylon inserts. INCLUDES: Four 5mm locknuts. SPECS: Thickness: 4.95mm (.195")

.

.

FEATURES: Replaces worn bearings Constructed of steel INCLUDES: Two 6x12x4mm Ball Bearings for the Traxxas T-Maxx Monster Truck REQUIRES: Installing two bearings in each axle carrier (4932) and two for each front and rear differential housings (4980)

FEATURES: Features strengthened plastic for long life and durability. These diff yokes are more rigid than the stock yokes. Black in color. INCLUDES: Two heavy duty diff yokes Two diff yoke mounting shafts REQUIRES: Assembly onto the vehicle.

FEATURES: Replaces damaged axle carriers and steering blocks. Constructed of black plastic. INCLUDES: One set of axle carriers and steering blocks for the Traxxas T-Maxx. REQUIRES: Bolting to each suspension arm (4931), installing two 6x12mm ball...

These pivot balls are installed through the upper and lower suspension arms and axle carriers and allow camber adjustment of the wheels. FEATURES: Replace stock pivot balls with these hardened heavy duty versions. Constructed of 7075 T-6 aluminum...

FEATURES: Replaces stock plastic bumpers. Constructed of molded silver colored plastic. INCLUDES: One dual-tube front bumper One dual-tube rear bumper REQUIRES: Fastening each bumper to the bumper mounts (4936) with four 3x12mm buttonhead cap screws (not...

FEATURES: Attaches to and protects chassis and supports the front bulkhead Skidplate is gray in color INCLUDES: Skidplate and stainless steel plate REQUIRES: Installing on chassis with four 3x12mm countersunk machine screws (not included, use...

FEATURES: Replaces damaged rear skidplates. Constructed of black plastic. INCLUDES: One rear skidplate. REQUIRES: Bolting to bottom of chassis using three 3x10mm countersunk machine screws (not included).

FEATURES: Attaches to and protects chassis and supports the rear bulkhead Skidplate is gray in colorINCLUDES: Skidplate and stainless steel plateREQUIRES: Installing on chassis with four 3x12mm countersunk machine screws (not included, use 2552)COMMENTS:...

FEATURES: Durable steel construction INCLUDES: Eight pins REQUIRES: Assembly onto T/E-Maxx SPECS: Length: 65.3mm (2.57") Diameter: 3.2mm (.13") COMMENTS: These are enough hinge pins for the entire vehicle.

FEATURES: Attaches to and protects chassis and transmission Skidplate is gray in color Nylon construction INCLUDES: One Skidplate REQUIRES: Installing on chassis  

FEATURES: Fits first generation T-Maxx transmission without Optidrive Steel shaft with plastic gear 22T and 17T gears Pre-assembled on shaft INCLUDES: One transmission input shaft REQUIRES: Installation into gearbox SPECS: Length: 2.20" (56mm) Shaft...

FEATURES: Stainless Construction Blue Rubber Sealed INCLUDES: Two 8mm x 16mm Rubber Sealed Bearings REQUIRES: Assembly onto Vehicle SPECS: Inner Diameter: 8mm (0.31") Outer Diameter: 16mm (0.62") Thickness: 5mm (0.19")

.

FEATURES: Black plastic construction INCLUDES: One front shock mount One rear shock mount Four chassis wire clips Four 3x32mm caphead machine screws Four 3x6mm buttonhead machine screws  

FEATURES: Steel idler gear construction Plastic idler gear support construction Idler gear support is black in color Idler gear bearing preinstalled INCLUDES: One idler gear Part #5377 One idler gear support Part #5377 One 5X10mm ball bearing REQUIRES:...

FEATURES: Plastic shift fork construction Metal shift fork shaft Shift fork plastic is black in color Preassembled INCLUDES: One shift fork and shaft, Part #5389 REQUIRES: Installation on the Traxxas Revo

FEATURES: Constructed of hardened steel INCLUDES: Differential Output Gear for the Traxxas Revo 3.3 REQUIRES: Installing in front or rear of center differential COMMENTS: WIll not work with Rear Brake Kit #5417

FEATURES: 1.4 lb/in tension Red coating INCLUDES: Two Shock Springs REQUIRES: Assembly onto the Traxxas Slayer Shocks SPECS: Length: 51mm (2") Diameter: 21mm (0.83")

FEATURES: 1.6 lb/in tension Red coating INCLUDES: Two Shock Springs REQUIRES: Assembly onto the Traxxas Slayer Shocks SPECS: Length: 49mm (1.9") Diameter: 22mm (0.87")

FEATURES: Spring Steel Construction Red Outer Nylon Coating Yellow 2.6 tension rating INCLUDES: Two Red 2.6 Springs for the Traxxas GTR Shocks used on the Revo REQUIRES: Nothing SPECS: Length: 1.8" (46mm) Outer diameter: 0.83" (21mm) Wire diameter: 0.08"...

FEATURES: Red in color Orange band on spring indicates 3.2 tension rating INCLUDES: Two 3.2 rear shock springs REQUIRES: Nothing. These are direct fit springs. SPECS: Length: 1-3/4" (44mm) Outer diameter: 0.83" (21mm)

FEATURES: Red in color Green band on spring indicates 3.5 tension rating INCLUDES: Two 3.5 rear shock springs REQUIRES: Nothing. These are direct fit springs. SPECS: Length: 90mm (3.5") Outer diameter: 21mm (0.83")

FEATURES: Red in color (small gold square indicates spring type) Metal construction INCLUDES: 2 springs SPECS: Length: 1-11/16" (43mm) Inside diameter: 11/16" (17mm) Outside diameter: 7/8" (22mm) Spring Rate: 3.8

FEATURES: Red in color Tan band on spring indicates 4.1 tension rating INCLUDES: Two 4.1 rear shock springs REQUIRES: Nothing. These are direct fit springs. SPECS: Length: 1-3/4" (44mm) Outer diameter: 0.83" (21mm)

FEATURES: Steel construction Painted red w/small black stripe 4.4 tension rate (slightly lighter than stock rear spring) INCLUDES: Two 4.4 Black Rate Shock Springs for the Traxxas Revo REQUIRES: Assembly to vehicle SPECS: Static Length: 50mm (1.77") Wire...

FEATURES: Steel construction Painted red w/small silver stripe 4.9 tension rate (Light) INCLUDES: Two Shock Springs REQUIRES: Assembly to vehicle SPECS: Static Length: 50mm (1.77") Wire Diameter: 2.5mm (.10")

FEATURES: Red in color (small blue square indicates spring type) Metal construction INCLUDES: 2 springs REQUIRES: Installation on the Revo SPECS: Length: 1-11/16" (43mm) Inside diameter: 11/16" (17mm) Outside diameter: 7/8" (22mm) Spring Rate: 5.9

FEATURES: Red in color (small purple square indicates spring type) Metal construction INCLUDES: 2 springs REQUIRES: Installation on the Revo SPECS: Length: 1-11/16" (43mm) Inside diameter: 11/16" (17mm) Outside diameter: 7/8" (22mm) Spring Rate: 6.4

FEATURES: Polished aluminum construction INCLUDES: Two Shock Shafts REQUIRES: Installin in shock set  SPECS: Length: 1.8" (47mm) Diameter: 0.14" (3.5mm) shaft 0.098" (2.5mm) threads

FEATURES: Nylon construction Black in color INCLUDES: One Left and Right 30° Caster Blocks One Left and Right 30° Steering Blocks REQUIRES: Assembly onto Vehicle

FEATURES: Nylon construction Black in color INCLUDES: One Left and Right 25° Caster Blocks One Left and Right 25° Steering Blocks REQUIRES: Assembly onto Vehicle

FEATURES: Nylon construction Gray in color INCLUDES: One Left and Right Steering Bellcrank One Servo Saver One Servo Saver Spring Two Steering Supports Four 4mm x 7mm x 2.5mm Plastic Bushings REQUIRES: Assembly onto Vehicle

FEATURES: Nylon construction Black in color INCLUDES: One Servo Arm for Airtronics, KO, and Sanwa One Servo Arm for JR One Servo Arm for Hitec Three Servo Case Mounts REQUIRES: Assembly onto Vehicle

FEATURES: Metal and nylon construction Black in color INCLUDES: Two Metal Rear Stub Axles w/Nylon Yokes installed REQUIRES: Assembly onto Vehicle

FEATURES: Metal Construction Black in color INCLUDES: One Input Shaft (Slipper Shaft) One Slipper Shaft Spacer REQUIRES: Assembly onto Vehicle

FEATURES: Nylon construction Black in color INCLUDES: Front and Rear Body Mount Posts REQUIRES: Installation on the vehicle

FEATURES: Steel construction, red in color 4.9 damping rate with double yellow stripe marking INCLUDES: Two Long Springs for the Traxxas GTR shocks REQUIRES: Installation on shock assembly SPECS: Length: 2" (51mm) Diameter: 0.87" (22.2mm)

FEATURES: Steel construction, red in color 5.4 damping rate with double orange stripe marking INCLUDES: Two Long Springs for the Traxxas GTR shocks REQUIRES: Installation on shock assembly SPECS: Length: 2" (51mm) Diameter: 0.87" (22.2mm)

FEATURES: Plastic construction, black in color INCLUDES: Center half shafts (three internal splined and two external splined) REQUIRES: Installation on the vehicle SPECS: Diameter: 17.2mm (0.68")

FEATURES: Nylon construction Black in color INCLUDES: One Heavy Duty Differential Carrier One Front and Rear Linkage Arm One Differential Fork Two X-Ring Gaskets One Ring Gear Gasket Two Bushings One 6.5x10x0.5mm Washer REQUIRES: Installation on the...

FEATURES: JST Connectors INCLUDES: One Center Harness One Wire Clip Three Zip Ties REQUIRES: Installation on vehicle

FEATURES: Black nylon constructionINCLUDES: One Battery Hold Down          One Retainer Hold Down          One Battery...

This is the Lower Chassis for use with the optional Traxxas #5830 Slash 2WD Low CG Conversion Kit. FEATURES: Plastic construction, black in colorFastens under front section of low CG chassis INCLUDES: Lower Chassis in Black SPECS: Length: 5.6"...

FEATURES: 2.3 lb/in tension Red coating INCLUDES: Two Shock Springs REQUIRES: Assembly onto the Traxxas Slayer Shocks SPECS: Length: 49mm (1.9") Diameter: 22mm (0.87")

.

Includes: - Main Frame (2) - Battery Holder (1) - Canopy Mounting Posts (2) - Screws (2)

.

.

FEATURES: Molded plastic construction INCLUDES: Splitter Extension with two 3x10mm Countersunk Screws

FEATURES: Dense foam absorbs minor impacts INCLUDES: Foam Front Bumper for the Traxxas XO-1 SPECS: Width: 10.1" (258mm) Thickness: 0.98" (25mm)

.

FEATURES: Composite construction Holds stock 7-cell battery supplied with vehicle INCLUDES: Two battery Hold Down sections with metal Post and Body Clip REQUIRES: Fastening to chassis COMMENTS: Also available in a different shape to hold taller...

FEATURES: Composite construction Allows installation of taller multi-cell batteries INCLUDES: Battery Hold Down with metal Post and Body Clip REQUIRES: Fastening to chassis

FEATURES: Hardened steel construction INCLUDES: Internal Splined Half Shaft

FEATURES: Hardened plastic construction Black in color INCLUDES: One rear bulkhead

FEATURES: Hardened plastic construction Black in color INCLUDES: One front shock tower REQUIRES: Installation on chassis SPECS: Length: 71mm (2.80") Width: 49mm (1.93")  

Fits Continued: 1/10 Nitro Slash FEATURES: Aluminum construction INCLUDES: 2 rear stub axles 2 pins REQUIRES: Installation on vehicle

FEATURES: Nylon construction          Red in colorINCLUDES: Four Pushrods          Eight Hollow Balls

FEATURES: Aluminum construction          Blue in colorINCLUDES: One Front Bulkhead Tie Bar          One Rear Bulkhead Tie...

FEATURES: Nylon construction, black in colorINCLUDES: Two Rear Bulkhead Sections          Four 3 x 10mm Button Head Screws          One 2.5 x 22mm  Socket Head...

FEATURES: Nylon construction          Black in colorINCLUDES: Two front bulkhead halves          Four 3x10mm Button Head...

FEATURES: Nylon constructionBlack in colorINCLUDES: Left Front & Rear Axle CarrierRight Front & Rear Axle Carrier

FEATURES: Nylon construction          Red in colorINCLUDES: Two Front and two Rear Toe Links          Eight Hollow Balls

FEATURES: Nylon construction          Black in color          Fits left or rightINCLUDES: Two Internal Splined Half...

FEATURES: Nylon construction          Black in colorINCLUDES: One Front Center Half Shaft          One Rear Center Half...

FEATURES: Molded composite construction          Red in colorINCLUDES: Four Pushrods          Eight Hollow Balls

FEATURES: Molded composite construction          Green in colorINCLUDES: Four Pushrods          Eight Hollow Balls

FEATURES: Nylon construction, black in colorINCLUDES: One Wing          One Decal SetREQUIRES: Installation on the vehicleSPECS:    Length: 118mm (4...

FEATURES: Nylon construction          White in colorINCLUDES: One Wing          Decal SheetREQUIRES: Installation on the vehicleSPECS:    Length:...

FEATURES: Nylon construction          Red in colorINCLUDES: Four Front/Rear Toe Links          Eight Hollow Balls

FEATURES: Molded composite plastic construction, green in colorINCLUDES: Two Front and two Rear Toe Links          Eight Hollow Metal Balls

FEATURES: Nylon construction          Black in colorINCLUDES: Two Internal Splined Half Shafts          Two External Splined Half...

FEATURES: Plastic constructionINCLUDES: One-piece Rear and two-piece Front Body Mounts

FEATURES: Made of black plastic INCLUDES: One bulkhead SPECS: Length: 3" (76mm) Width: 2-13/16" (71mm) Height: 2" (51mm)

FEATURES: Made of black plastic. INCLUDES: One skid plate SPECS: Length: 3-11/16" (68mm) Width: 5-3/4" (146mm) Height: 1-1/8" (29mm)

.

.

FEATURES: Made of black rubber INCLUDES: Two tires SPECS: Diameter, outer: 1-11/16" (43mm) inner: 6mm (1/4") Width: 18mm (11/16")

    FEATURES One-piece molded composite plastic construction Installs between skid plate and lower bulkhead to help hold front and rear bulkhead assemblies in place   ...