Traxxas

FEATURES: Black plastic construction INCLUDES: Two differntial output yokes Two 3x5mm countersunk screws Two screw pins REQUIRES: Installation SPECS: Length: .70" (18mm) Diameter: .51" (13mm)

Fits Continued: 1/10 Slash R.G.D. / Ford Raptor / Nitro Jato 3.3 / Revo / T-Maxx FEATURES: Constructed of hard plastic Axles constructed of steel INCLUDES: Four wheels and two axles REQUIRES: Installing on wheelie bar SPECS: Thickness: 0.39" (10mm)...

FEATURES: Replaces damaged or worn spur gears Constructed of plastic INCLUDES: One 43 Tooth 1st Speed Spur Gear for the Traxxas T-Maxx Truck REQUIRES: Installing in gearbox between the drive hub assembly (4988) and the primary gears (4995)

FEATURES: Replaces damaged or worn spur gear assemblies Constructed of plastic INCLUDES: One spur gear assembly REQUIRES: Diassembly of gearbox and installing spur gear onto primary gear shaft (4993)

This is a 2 pack of Traxxas 5X8mm Ball Bearings. FEATURES Metal bearing construction Blue rubber dirt shields INCLUDES (2) 5X8mm ball bearings Part...

FEATURES: Steel construction Blue rubber dirt shields INCLUDES: (2) ball bearings, Part #5117 SPECS: Inside diameter: 6mm Outside diameter: 12mm Width: 4mm

FEATURES: Rubber shielded          Steel constructionINCLUDES: Two rubber shielded bearingsREQUIRES: NothingSPECS:    Thickness: 2.6mm          Inner...

.

FEATURES: Stainless Steel bearing construction Blue rubber dirt shields INCLUDES: (2) 6x13x5mm ball bearings Part #5180 SPECS: Inside diameter: 6mm (0.24") Outside diameter: 13mm (0.51") Width: 5mm (0.20")

.

FEATURES: Silicone construction Blue in color INCLUDES: One Tune Pipe Coupler One Exhaust Deflector (for use on the tune pipe) One short Tie-Strap Two long Tie-Straps REQUIRES: Assembly to vehicle SPECS: Coupler Length: 24mm (.95") Coupler Inner...

FEATURES: Nylon construction, black in color INCLUDES: One Throttle Servo Mount Two 4x10 Socket Head Screws REQUIRES: Installation SPECS: Length: 80mm (3.15") Width: 27mm (1.06") Height: 20mm (0.79")

FEATURES: Plastic construction Black in color Metal Pivot Balls INCLUDES: Six Rod Ends Six Pivot Balls REQUIRES: Assembly to vehicle SPECS: Length: 18mm (.71") Width at ball joint: 9.5mm (.38")

FEATURES: Steel construction Black in color INCLUDES: One input shaft, Part #5366 REQUIRES: Installation on the Traxxas Revo SPECS: Length: 2-3/16" (56mm) Diameter: 3/16" ( 5mm)

FEATURES: Durable black nylon constructionINCLUDES: One diff housing (2 pieces)REQUIRES: 5119 10x15mm Bearing (1) 5118 8x16mm Bearing (1) 5117 6x12mm Bearings (2) 5381 Diff Carrier & Gasket 3965 Cap Head Screw 2.5X8MM 2587 Cap Head Screw 3X10MM 5329...

FEATURES: Nylon construction INCLUDES: Gear, two ring seals, gasket and instruction sheet REQUIRES: Installing in diff case according to instructions on sheet COMMENTS: Fits only the optional Revo Center Differential Kit.

FEATURES: Black plastic construction INCLUDES: Two yokes Two drive pins REQUIRES: Nothing. These are direct replacement parts.

FEATURES: Plastic Brake Yoke Steel Brake Pins(each knurled on one end) Steel Screw Pins INCLUDES: One Brake Yoke Two Brake Pins One Screw Pin REQUIRES: Assembly to the vehicle SPECS: Brake Yoke Outer Diameter: 18.5mm (.73") Brake Yoke Center Key Size:...

FEATURES: Black plastic construction INCLUDES: Two drive yokes Two 4x15mm Yoke pins REQUIRES: T-Maxx 3.3 SPECS: Length: 15/16" (23mm) Diameter: 3/4" (17mm)

FEATURES: Plastic construction Black in color INCLUDES: One Rear Bumper. REQUIRES: Assembly onto Vehicle

FEATURES: Heavy duty plastic construction Black in color INCLUDES: Eight Rod Ends REQUIRES: Threading onto suspension and steering rods SPECS: Length: 31.5mm (1.24") Width at ball joint: 11mm (0.43")

FEATURES: Anodized Blue Aluminum crimp nut INCLUDES: One crimping nut Nylon wrench

FEATURES: Anodized red aluminum crimp nut INCLUDES: One Crimp Nut Nylon wrench

FEATURES: Nylon construction Black in color INCLUDES: Two Differential Output Yokes Two 2.6mm Set Screw Pins REQUIRES: Assembly onto Vehicle

FEATURES: Nylon and Metal construction Black in color INCLUDES: One 3mm x 30mm Threaded Rod Two 3mm Ball Cups Two 3mm Hollow Balls One Nylon Steering Servo Horn REQUIRES: Assembly onto Vehicle

FEATURES: Composite construction Grey in color INCLUDES: One Composite Brake Disc REQUIRES: Assembly onto Vehicle  

FEATURES: Prevents moisture and dirt from entering receiver box INCLUDES: Silicone rectangle shaped O-ring Silicone grease, TRAC6037 Two sections of foam rubber Instruction sheet REQUIRES: Installing between receiver box sections

FEATURES: Nylon construction Black in color INCLUDES: One Differential Housing REQUIRES: Installation on the vehicle

These are the Low CG Nerf Bars in Blue for the 1/10 scale 2WD Traxxas Slash. FEATURES: Plastic construction, blue in colorFor use with the Low CG chassisFastens to sides of chassis to absorb impacts INCLUDES: Two Nerf Bars

These are the Low CG Nerf Bars in Blue for the 1/10 scale 2WD Traxxas Slash. FEATURES: Plastic construction, blue in colorFor use with the Low CG chassisFastens to sides of chassis to absorb impacts INCLUDES: Two Nerf Bars

FEATURES: Seals receiver box from dirt and moisture INCLUDES: Silicone O-Ring Two sections of Foam Tape Silicone Grease Instruction Sheet

13-tooth pinion gear. Fits 5mm shaft, 1.0 metric pitch. Hardened steel for use with steel spur gears. Includes set screw.

This is the optional 15 Tooth Pinion Gear for the Traxxas X-Maxx. FEATURES Hardened steel construction Replaces stock 6491X 18T pinion gear Compatible with steel spur gears Fits 0...

This is an optional Traxxas RPM Sensor Mount Set, and is intended for use with a Traxxas nitro vehicle when wanting to use the optional Traxxas RPM sensor (TRA6520/TRA6522). The sensor mount positions the RPM sensor to properly read the trigger magnet...

.

FEATURES: Constructed of clear plastic INCLUDES: One rear shaft cover REQUIRES: Installation

FEATURES: Black plastic construction INCLUDES: 2 Ouput yokes 2 screw pins REQUIRES: Installation on vehicle

FEATURES: Durable steel construction Silver in color INCLUDES: Four 51.5mm pins Four 30mm pins

FEATURES: Clear nylon construction INCLUDES: One Center Driveshaft Cover REQUIRES: Installation over driveshaft SPECS: Length: 210mm (8.3") Width: 15mm (0.59")

FEATURES: Hardened plastic construction          Black in colorINCLUDES: One motor mount assembled with a 3x6mm flat head machine screw          One 3mm locknut

FEATURES: Hardened plastic construction Black in color INCLUDES: Two rear differential housing halves REQUIRES: Installation around diff components

FEATURES: Steel construction INCLUDES: Two shock shafts COMMENTS: These shafts get installed into the shock bodies.

FEATURES: Blue rubber sealed          May also be used in any vehicle where this size bearing is requiredINCLUDES: Two Ball BearingsREQUIRES: Installation on the vehicleSPECS:    Outer Diameter:...

FEATURES: Ball bearings          Blue rubber sealedINCLUDES: Two Ball BearingsREQUIRES: Installation on the vehicleSPECS:    Outer Diameter: 12mm (0...

FEATURES: Prevents moisture and dirt from entering receiver boxINCLUDES: Silicone O-ring          Silicone grease          Two sections of foam...

FEATURES: Nylon construction          Black in colorINCLUDES: Twenty Hollow BallsREQUIRES: Installation on the vehicleSPECS:    Outer Diameter: 4.5mm (0...

FEATURES: Black nylon constructionINCLUDES: Eight Nylon Rod Ends          Eight Nylon flanged Balls

FEATURES: Aluminum construction          Silver in colorINCLUDES: Two Shock Shafts

FEATURES: Steel construction          Red in color          0.82 rate, double orangeINCLUDES: Two GTR Shock SpringsREQUIRES: Installation on the...

FEATURES: Steel construction          Red in color          Double green          0.88 rateINCLUDES: Two Shock...

FEATURES: Steel construction          Red in color          1.02 rate, double tanINCLUDES: Two GTR Spring ShocksREQUIRES: Installation on the...

FEATURES: Steel construction          Red in color          1.15 rate, double blackINCLUDES: Two Shock SpringsREQUIRES: Installation on the...

FEATURES: Steel construction          Red in color          1.76 rate, orangeINCLUDES: Two Shock SpringsREQUIRES: Installation on the...

FEATURES: Steel construction          Red in color          Green          1.92 rateINCLUDES: Two Shock Springs

FEATURES: Steel construction          Red in color          2.06 rate, tanINCLUDES: Two GTR Shock SpringsREQUIRES: Installation on the shock...

.

FEATURES: Spring,shock(GTR) for 1/16 SummitINCLUDES: Two SpringsREQUIRES: Installation onto shocksSPECS:    Spring Rate:  (Pink)          Length:      ...

FEATURES: Steel construction with nickel finish          Pink compression ratingINCLUDES: Two Shock Springs

FEATURES: Spring,shock(GTR) for 1/16 SummitINCLUDES: Two SpringsREQUIRES: Installation onto shocksSPECS:    Spring Rate:  Blue          Length:      ...

FEATURES: Steel construction with nickel finish          Blue compression ratingINCLUDES: Two Shock Springs

FEATURES: GTR shock springs for the 1/16 Summit          Steel constructionINCLUDES: Two SpringsREQUIRES: Installation onto shocksSPECS:    Spring Rate:  3.2...

FEATURES: Composite constructionINCLUDES: Motor Cover, Motor Mount Hinge Post, 3x10mm Screw with split and            Falt Washers, 2.5 x 4mm Screw and two 3x8mm Screws

FEATURES: Made of black plastic, these are mounted to the side of the car to protect agains side impacts. INCLUDES: Two nerf bars SPECS: Length: 5-1/2" Width: 1-7/8" Height: 2-1/4"

.

 

FEATURES: Plastic construction white in color INCLUDES: Two 12-Spoke Wheels

FEATURES Replaces damaged or missing receiver box seal and cushions Silicone grease helps to seal receiver box to chassis   INCLUDES Two Foam...

FEATURES Steel construction Fastens lower rear suspension arms to chassis   INCLUDES Two 4x85mm Suspension Pins   ...

FEATURES Molded composite plastic construction   INCLUDES Servo Horn Steering Linkage with Pressed-In Steel Balls

Rebuild kit for use with #7750X heavy duty X-Maxx driveshaft. Kit includes pins for 2 driveshaft assemblies.

FEATURES Molded composite plastic construction   INCLUDES Differential Carrier Two X-Ring Gaskets Two Ring Gear Gaskets

Description: Traxxas Body mounts, Front & Rear (fits #8311 body) (2) This item package consists of the following Traxxas items. Body mounts, front & rear (fits #8311 body) (2)  

Description: Traxxas Body Bumper, Foam - TRA8319 This item package consists of the following Traxxas items. Body bumper, foam   For FORD GT

Description: Traxxas Caster Blocks This item package consists of the following Traxxas items. Caster blocks (c-hubs) (2)/ kingpin bushings (4)   For FORD GT

Description: Traxxas Mounts, Suspension Arms This item package consists of the following Traxxas items. Mounts, suspension arms (front & rear) (4)/ hinge pin retainers (2)   For FORD GT

Description: Traxxas Steering Blocks (2) This item package consists of the following Traxxas items. Steering block (2)   For FORD GT

Description: Traxxas Camber Link This item package consists of the following Traxxas items. Camber link/toe link set (plastic/ non-adjustable) (front & rear)   For FORD GT

.

.

Description: Traxxas Carriers, Stub Axle (Left & Right) - TRA8352 This item package consists of the following Traxxas items. Carriers, stub axle (left & right)   For FORD GT

Description: Traxxas Drive Cups - TRA8353 This item package consists of the following Traxxas items. Drive cups, inner (2)/ screw pins (2)   For FORD GT

Description: Traxxas Wheel Hubs (4) - TRA8356 This item package consists of the following Traxxas items. Wheel hubs, hex (disc brake rotors) (4)   For FORD GT

Description: Traxxas Housing, Differential (Rear) - TRA8380 This item package consists of the following Traxxas items. Housing, differential (rear)   For FORD GT

Description: Traxxas Housing, Differential (Front) - TRA8381 This item package consists of the following Traxxas items. Housing, differential (front)   For FORD GT

Ball bearings, black rubber sealed (4x10x4mm) (2)

Ball bearings, black rubber sealed (6x12x4mm) (2)

Ball bearings, black rubber sealed (7x14x5mm) (2)

.

.

.

These are replacement Main Frame Lower Portion for the LaTrax Alias Quad-Copter Includes: 1 x Black Main Frame Lower 4 x 1.6x5mm BCS (self-tapping) screws

.

.

.

.

.

FEATURES; Pre-Molded White Plastic Wheels Cone-Dish Design Dyeable White Plastic INCLUDES: 2-Front Wheels SPECS: 2.2" Diameter 3/4" wide REQUIRES: Customer will need to purchase front tires separately, they will need tires with inside diameter of 2.2"

FEATURES: Clear silicone construction INCLUDES: One Silicone Tube SPECS: Length: 203mm (8") Inner diameter: 8mm (0.32") Outer diameter: 14mm (0.55")

FEATURES: Black nylon construction INCLUDES: One L&R Front Bumper Mount Set One L&R Rear Bumper Mount Set Eight 3x15mm round head machine screws REQUIRES: Nothing. This is a direct replacement part.